STM32CubeMX教程22 FSMC - 8080并行接口TFT-LCD驱动
1、准备材料
开发板（
正点原子stm32f407探索者开发板V2.4
）
STM32CubeMX软件（
Version 6.10.0
）
keil µVision5 IDE（
MDK-Arm
）
2、实验目标
使用STM32CubeMX软件配置STM32F407开发板
FSMC接口驱动8080并行接口TFT-LCD显示
，具体为使用FSMC Bank 1-NOR/PSRAM4，片选信号为NE4（PG12），TFT-LCD的RS引脚接FSMC地址线A6（PF12）来驱动TFT-LCD进行不同颜色刷屏显示
3、实验流程
3.0、前提知识
开发板使用TFT-LCD时最好使用外接电源给开发板供电，如果使用单USB供电可能会出现电流不足电压波动TFT-LCD初始化失败的现象
，以下TFT-LCD全部简称为LCD
3.0.0、FSMC概述
FSMC全称为灵活的静态存储控制器，其时钟信号为HCLK，FSMC根据支持的存储器类型可以分为NOR/PSRAM、NAND Flash和PC卡三种，本实验只涉及第一种NOR/PSRAM，严格意义上讲也与NOR/PSRAM无关，只是使用其中的LCD Interface类型的内存类型，下图中2号红框中标出了本此实验需要使用的FSMC的一些引脚，主要包括片选引脚、地址线、数据线、输出和写入等，如下图所示为FSMC的具体框图
（注释1）
从FSMC的角度，外部存储器被划分为4个固定大小的存储区域，每个存储区域的大小为256 MB，存储区域1可连接4个NOR Flash或PSRAM存储器器件，此存储区域被划分为4个NOR/PSRAM区域，带4个专用片选信号NE1/2/3/4，每个区域大小为64MB，FSMC的具体存储区域映射如下图所示
通过FSMC写入外部存储设备需要知道写入的地址，该地址有HADDR所确定，HADDR是AHB内部地址线，但也会参与对外部存储器的寻址，
其HADDR[27:26]两个位用于选择从地址0X6000 0000到地址0x6FFF FFFF处分成4个部分的存储区域，HADDR[25:0]的26个位用于地址线，确定写入选中存储区域中的地址
，如下图所示位HADDR的解释
（注释2）
由于 HADDR 为字节地址，而存储器按字寻址，据存储器数据宽度不同，实际向存储器发送的地址也将有所不同，
当存储器宽度为16位（16根数据线）时，向存储器发出的数据地址将自动向右偏移一位
，具体如下表所
3.0.1、为什么使用FSMC控制LCD?
FSMC一般是用来连接SRAM、PSRAM、ROM和NOR Flash等存储设备的，为什么要使用FSMC来控制8080并口的LCD呢？
先来看一看这些存储设备和8080并口LCD的引脚，SRAM的接口如下图所示
（注释3）
8080并口LCD的接口引脚如下图所示
可以发现LCD的接口中除去RST和背光BLK引脚外，其他的引脚均可以由FSMC来提供，RS引脚可以选择FSMC的26位地址线中的一根控制，片选信号可以由FSMC的NEx引脚提供，RD由NOE提供，WR由NWE提供，D0-D15可以与FSMC的16跟数据线直接连接
所以在FSMC的NORFIash/PSRAM/SRAM/ROM/LCDx中也有一个专门的LCD Interface类型的内存类型，因此我们其实可以把8080并口的LCD当成一个存储设备通过FSMC来控制
3.0.2、LCD接口硬件原理详解
如下图所示为LCD接口硬件原理图
- 8080并口LCD的片选信号CS可以直接使用FSMC的NEx引脚，这里使用FSMC Bank 1-NOR/PSRAM4来控制LCD，因此CS接FSMC_NE4
- LCD写入引脚WR接FSMC的写入使能引脚FSMC_NWE
- LCD的读操作引脚接FSMC的输出使能引脚FSMC_NOE
- LCD寄存器选择引脚RS接26位地址线上任何一根都可以，这里接入了A6
- 16位数据线直接对接
- LCD的复位引脚与开发板复位引脚相连，使用开发板复位引脚可以同时复位MCU和LCD
- LCD的背光引脚由PB15引脚控制，当高电平时背光被点亮
3.0.3、控制FSMC对LCD命令/数据写入（重点）
使用FSMC写LCD时一般分为写数据（选择数据寄存器）或者写命令（选择控制寄存器），而LCD的RS引脚负责决定选择数据还是控制寄存器，如果RS引脚是高电平1，则选择数据寄存器；如果RS引脚引脚为低电平0，则选择控制寄存器
FSMC的地址线一共有26位（FSMC_A[25:0]），对于LCD来说，只需要任选其中一根地址线与RS引脚连接即可实现对LCD写数据/命令的控制，但是选择不同地址线所对应的控制写命令/数据的地址也不相同
以本实验为例，此时LCD使用FSMC Bank 1-NOR/PSRAM4，其起始地址为0x6C00 0000，LCD的RS引脚接FSMC地址线A6（PF12），且此时LCD为16位宽度数据传输，FSMC会将写入的地址自动向右偏移一位，
因此LCD的RS引脚选择控制寄存器只需要在起始地址基础上满足A7位为0即可，比如可以是0x6C00 0000，也可以是0x6C00 0040等；LCD的RS引脚选择写数据寄存器只需要在起始地址基础上满足A7位为1即可，比如可以是0x6C00 0080，也可以是0x6C00 00C0等；
因此我们可以直接定义FSMC写LCD命令/数据的地址，第一种方法源代码如下所示
/*LCD写命令地址*/
#define LCD_REG (*((volatile unsigned short *) 0x6C000000))
/*LCD写数据地址*/
#define LCD_RAM (*((volatile unsigned short *) 0x6C000080))
/*将数据data写入LCD数据寄存器*/
LCD_RAM = data;
/*将寄存器值regval写入LCD控制寄存器*/
LCD_REG = regval;
除了上述的方法外，常见的还有一种定义LCD地址结构体的方法，其原理一致，但读者理解的时候可能不太容易理解，接下来由笔者仔细分析一下，第二种方法源代码如下所示
/*定义LCD地址结构体*/
typedef struct
{
volatile uint16_t LCD_REG;
volatile uint16_t LCD_RAM;
}LCD_TypeDef;
/*LCD控制/数据寄存器基址*/
#define LCD_BASE ((uint32_t)(0x6C000000 | 0x0000007E))
#define LCD ((LCD_TypeDef *) LCD_BASE)
/*将数据data写入LCD数据寄存器*/
LCD->LCD_RAM=data;
/*将寄存器值regval写入LCD控制寄存器*/
LCD->LCD_REG=regval;
我们已经知道，当LCD的RS引脚接FSMC地址线A6，由于FSMC会将写入的地址自动向右偏移一位，因此写入数据（选择数据寄存器）时地址线A7应该为1，写入命令（选择控制寄存器）时地址线A7应该为0
而在结构体中先定义了uint16_t（2个字节）的LCD_REG变量，紧接着定义了uint16_t的LCD_RAM变量，
这两个变量在内存中的地址应该是连续的
并且我们将LCD变量强制转化为了LCD_TypeDef*类型的变量，同时将LCD_BASE的地址赋值给LCD，
因此LCD的地址应该为(0x6C000000 | 0x0000007E))，LCD->LCD_REG的地址应该同样为(0x6C000000 | 0x0000007E))，而LCD->LCD_RAM的地址应该为(0x6C000000 | 0x0000007E+2))
此时读者应该可以发现
通过结构体中顺序定义的变量在内存中地址连续这一特点，LCD->LCD_REG表示了地址线A7为0，LCD->LCD_RAM表示了地址线A7为1
，也即通过LCD->LCD_REG可以写入LCD命令，通过LCD->LCD_RAM可以写入LCD数据
再举个例子，如果LCD的RS引脚接FSMC地址线的A12呢？
此时写入数据（选择数据寄存器）时地址线A13应该为1，写入命令（选择控制寄存器）时地址线A13应该为0
则按照第一种方法，可定义为如下代码
/*LCD写命令地址*/
#define LCD_REG (*((volatile unsigned short *) 0x6C000000))
/*LCD写数据地址*/
#define LCD_RAM (*((volatile unsigned short *) 0x60002000))
按照第二种方法，可定义为如下代码
/*LCD控制/数据寄存器基址*/
#define LCD_BASE ((uint32_t)(0x6C000000 | 0x00001FFE))
#define LCD ((LCD_TypeDef *) LCD_BASE)
一个小技巧，在使用第二种方法确定 LCD_BASE 地址时，假如RS接FSMC的地址线A6，则从右边往左数到A7位
（中间全是1，两边两个0）
，0666666 6666660（0x7E）；假如RS接FSMC的地址线A12，同样从右边往左数到A13位，01 6666661 6666661 6666660（0x1FFE）；
3.0.4、FSMC时序参数设置
查看LCD使用的控制芯片NT35510的芯片数据手册
（注释4）
在361页的7.6.1并行接口特性（80 系列 MCU）小节中说明了使用8080并行接口控制的LCD所需要满足的时序和信号特征的最大最小值
如下图中表格所示，重点看表格中读写的地址建立时间和数据建立时间，其规定了最小需要的时间
在STM32CubeMX中可以设置读写时序的地址建立时间和数据建立时间，单位为一个HCLK时钟周期，当HCLK时钟频率为STM32F407最高频率168MHz时，一个周期大约为6us
这里按照手册理论上读地址建立时间>10ns（2个HCLK时钟周期），写地址建立时间>0us，数据建立/保持时间>15+10ns（5个HCLK时钟周期），读写地址保持时间>2ns
，但生成代码中读写地址保持时间默认15个HCLK时钟周期，在软件上不可调，另外
总线翻转时间设置为0，访问模式选择A即可
因此综上所述，将参数从上到下设置为2、5、0、A、0、5、0和A（笔者在正点原子探索者开发板上使用4.3寸NT35510控制的LCD上验证可以使用），实际使用中如果出现问题可以增大参数值，具体配置如下图所示
再举个例子，如果你的LCD使用的控制芯片为ILI9341
，那么找到ILI9341芯片数据手册
（注释5）
在手册238页18.3.1小节中找到8080并口控制时的时序参数要求，如下图所示，根据手册我们可以知道理论上读/写地址建立时间>0ns，数据建立/保持时间>10+10ns（4个HCLK时钟周期），读写地址保持时间>0ns
因此在STM32CubeMX中参数从上到下设置为0、4、0、A、0、4、0和A即可（笔者在正点原子探索者开发板上使用野火3.2寸ILI9341控制的LCD上验证可以使用）
3.1、CubeMX相关配置
3.1.0、工程基本配置
打开STM32CubeMX软件，单击ACCESS TO MCU SELECTOR选择开发板MCU（选择你使用开发板的主控MCU型号）选中MCU型号后单击页面右上角Start Project开始工程，具体如下图所示
开始工程之后在配置主页面System Core/RCC中配置HSE/LSE晶振，在System Core/SYS中配置Debug模式，具体如下图所示
详细工程建立内容读者可以阅读“
STM32CubeMX教程1 工程建立
”
3.1.1、时钟树配置
系统时钟使用8MHz外部高速时钟HSE，HCLK、PCLK1和PCLK2均设置为STM32F407能达到的最高时钟频率，具体如下图所示
3.1.2、外设参数配置
单击Pinout & Configuration页面左边Connectivity/FSMC选项，
在右边的Mode下点开NORFIash/PSRAM/SRAM/ROM/LCD4选项卡（因为LCD使用的是使用FSMC Bank 1-NOR/PSRAM4），选择片选信号NE4，内存类型为LCD Interface，LCD寄存器选择（RS引脚）选择FSMC地址线A6，数据Data为16位（D0-D15）
，具体配置如下图所示
然后在Configuration里面配置其读写时序，
为什么要这样配置？
可以阅读本实验“3.0.4、时序参数设置”小节，具体配置如下图所示
配置好之后可以与硬件原理图上的引脚对照以下，看看有没有漏掉哪些引脚或者那些引脚默认配置不正确，由于RESET引脚直接与MCU的NRST引脚连接，当按下开发板复位按键时，LCD也会被复位，
因此最后只需设置LCD的背光控制引脚即可
，具体配置如下图所示
3.1.3、外设中断配置
本实验无需配置任何中断
3.2、生成代码
3.2.0、配置Project Manager页面
单击进入Project Manager页面，在左边Project分栏中修改工程名称、工程目录和工具链，然后在Code Generator中勾选“Gnerate peripheral initialization as a pair of 'c/h' files per peripheral”，最后单击页面右上角GENERATE CODE生成工程，具体如下图所示
详细Project Manager配置内容读者可以阅读“
STM32CubeMX教程1 工程建立
”实验3.4.3小节
3.2.1、外设初始化调用流程
在STM32CubeMX中配置了FSMC之后，会在生成的工程代码中新增MX_FSMC_Init()函数，在该函数中对FSMC的模式和对FSMC的读写时序参数进行了配置，然后调用了HAL_SRAM_Init()初始化函数
在HAL_SRAM_Init()初始化函数中调用了HAL_SRAM_MspInit()，然后在HAL_SRAM_MspInit()函数中最终调用了HAL_FSMC_MspInit()
在HAL_FSMC_MspInit()函数中完成了FSMC的数据线、地址线、读和写等引脚的复用操作，并且使能了相应的时钟
如下图所示为FSMC初始化具体调用流程
3.2.2、外设中断调用流程
本实验无需配置任何中断
3.2.3、添加其他必要代码
首先需要添加LCD的驱动文件，该驱动文件中应该对LCD进行正常初始化操作，另外应该包含一些LCD的画图函数，比如绘制圆形、直线和矩形等函数，一般是按照LCD驱动芯片的手册进行编程，但是为了避免重复造轮子，这里的驱动文件直接使用正点原子提供的
（注释6）
，笔者对文件稍微整理了以下，具体源代码如下所示
tftlcd.c文件
点击查看代码
#include "tftlcd.h"
#include "stdlib.h"
#include "font.h"
#include "stdio.h"
//
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//ALIENTEK STM32开发板
//2.8寸/3.5寸/4.3寸/7寸 TFT液晶驱动
//支持驱动IC型号包括:ILI9341/NT35310/NT35510/SSD1963等
//正点原子@ALIENTEK
//技术论坛:www.openedv.com
//创建日期:2017/4/8
//版本：V4.0
//版权所有，盗版必究。
//Copyright(C) 广州市星翼电子科技有限公司 2014-2024
//All rights reserved
//*******************************************************************************
//V4.0 20266666611
//1，去掉大部分不常用驱动IC的支持
//2，新增对ST7789驱动IC的支持
//3，优化代码结构（精简源码）
//
//LCD的画笔颜色和背景色
uint32_t POINT_COLOR=0xFF000000; //画笔颜色
uint32_t BACK_COLOR =0xFFFFFFFF; //背景色
//管理LCD重要参数
//默认为竖屏
_lcd_dev lcddev;
//MCU频率为168MHz时的us延时
void delay_us(uint32_t nus)
{
uint32_t Delay = nus * 168/4;
do
{
__NOP();
}
while (Delay --);
}
//写寄存器函数
//regval:寄存器值
void LCD_WR_REG(volatile uint16_t regval)
{
regval=regval; //使用-O2优化的时候,必须插入的延时
LCD->LCD_REG=regval; //写入要写的寄存器序号
}
//写LCD数据
//data:要写入的值
void LCD_WR_DATA(volatile uint16_t data)
{
data=data; //使用-O2优化的时候,必须插入的延时
LCD->LCD_RAM=data;
}
//读LCD数据
//返回值:读到的值
uint16_t LCD_RD_DATA(void)
{
volatile uint16_t ram; //防止被优化
ram=LCD->LCD_RAM;
return ram;
}
//写寄存器
//LCD_Reg:寄存器地址
//LCD_RegValue:要写入的数据
void LCD_WriteReg(uint16_t LCD_Reg,uint16_t LCD_RegValue)
{
LCD->LCD_REG = LCD_Reg; //写入要写的寄存器序号
LCD->LCD_RAM = LCD_RegValue;//写入数据
}
//读寄存器
//LCD_Reg:寄存器地址
//返回值:读到的数据
uint16_t LCD_ReadReg(uint16_t LCD_Reg)
{
LCD_WR_REG(LCD_Reg); //写入要读的寄存器序号
delay_us(5);
return LCD_RD_DATA(); //返回读到的值
}
//开始写GRAM
void LCD_WriteRAM_Prepare(void)
{
LCD->LCD_REG=lcddev.wramcmd;
}
//LCD写GRAM
//RGB_Code:颜色值
void LCD_WriteRAM(uint16_t RGB_Code)
{
LCD->LCD_RAM = RGB_Code; //写十六位GRAM
}
//从ILI93xx读出的数据为GBR格式，而我们写入的时候为RGB格式。
//通过该函数转换
//c:GBR格式的颜色值
//返回值：RGB格式的颜色值
uint16_t LCD_BGR2RGB(uint16_t c)
{
uint16_t r,g,b,rgb;
b=(c>>0)&0x1f;
g=(c>>5)&0x3f;
r=(c>>11)&0x1f;
rgb=(b<<11)+(g<<5)+(r<<0);
return(rgb);
}
//当mdk -O1时间优化时需要设置
//延时i
void opt_delay(uint8_t i)
{
while(i--);
}
//读取个某点的颜色值
//x,y:坐标
//返回值:此点的颜色
uint32_t LCD_ReadPoint(uint16_t x,uint16_t y)
{
uint16_t r=0,g=0,b=0;
if(x>=lcddev.width||y>=lcddev.height)return 0; //超过了范围,直接返回
LCD_SetCursor(x,y);
if (lcddev.id == 0X5510) //5510 发送读GRAM指令
{
LCD_WR_REG(0X2E00);
}
else //其他IC(9341/5310/1963/7789)发送读GRAM指令
{
LCD_WR_REG(0X2E);
}
r=LCD_RD_DATA(); //dummy Read
if (lcddev.id == 0X1963) //对1963来说,是真读
{
return r; //1963直接读就可以
}
opt_delay(2);
r = LCD_RD_DATA(); //实际坐标颜色
//9341/5310/5510/7789 要分2次读出
opt_delay(2);
b = LCD_RD_DATA();
g = r & 0XFF; //对于9341/5310/5510/7789, 第一次读取的是RG的值,R在前,G在后,各占8位
g <<= 8; //9341/5310/5510/7789 需要公式转换一下
return (((r >> 11) << 11) | ((g >> 10) << 5) | (b >> 11));
}
//LCD开启显示
void LCD_DisplayOn(void)
{
if (lcddev.id == 0X5510) //5510开启显示指令
{
LCD_WR_REG(0X2900); //开启显示
}
else //9341/5310/1963/7789 等发送开启显示指令
{
LCD_WR_REG(0X29); //开启显示
}
}
//LCD关闭显示
void LCD_DisplayOff(void)
{
if (lcddev.id == 0X5510) //5510关闭显示指令
{
LCD_WR_REG(0X2800); //关闭显示
}
else //9341/5310/1963/7789 等发送关闭显示指令
{
LCD_WR_REG(0X28); //关闭显示
}
}
//设置光标位置
//Xpos:横坐标
//Ypos:纵坐标
void LCD_SetCursor(uint16_t Xpos, uint16_t Ypos)
{
if (lcddev.id == 0X1963)
{
if (lcddev.dir == 0) //x坐标需要变换
{
Xpos = lcddev.width - 1 - Xpos;
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(0);
LCD_WR_DATA(0);
LCD_WR_DATA(Xpos >> 8);
LCD_WR_DATA(Xpos & 0XFF);
}
else
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(Xpos >> 8);
LCD_WR_DATA(Xpos & 0XFF);
LCD_WR_DATA((lcddev.width - 1) >> 8);
LCD_WR_DATA((lcddev.width - 1) & 0XFF);
}
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(Ypos >> 8);
LCD_WR_DATA(Ypos & 0XFF);
LCD_WR_DATA((lcddev.height - 1) >> 8);
LCD_WR_DATA((lcddev.height - 1) & 0XFF);
}
else if (lcddev.id == 0X5510)
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(Xpos >> 8);
LCD_WR_REG(lcddev.setxcmd + 1);
LCD_WR_DATA(Xpos & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(Ypos >> 8);
LCD_WR_REG(lcddev.setycmd + 1);
LCD_WR_DATA(Ypos & 0XFF);
}
else //9341/5310/7789等设置坐标
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(Xpos >> 8);
LCD_WR_DATA(Xpos & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(Ypos >> 8);
LCD_WR_DATA(Ypos & 0XFF);
}
}
//设置LCD的自动扫描方向
//dir:0~7,代表8个方向(具体定义见lcd.h)
//9341/5310/5510/1963/7789等IC已经实际测试
//注意:其他函数可能会受到此函数设置的影响(尤其是9341),
//所以,一般设置为L2R_U2D即可,如果设置为其他扫描方式,可能导致显示不正常.
void LCD_Scan_Dir(uint8_t dir)
{
uint16_t regval=0;
uint16_t dirreg=0;
uint16_t temp;
//横屏时，对1963不改变扫描方向, 其他IC改变扫描方向！竖屏时1963改变方向, 其他IC不改变扫描方向
if ((lcddev.dir == 1 && lcddev.id != 0X1963) || (lcddev.dir == 0 && lcddev.id == 0X1963))
{
switch (dir) //方向转换
{
case 0:
dir = 6;
break;
case 1:
dir = 7;
break;
case 2:
dir = 4;
break;
case 3:
dir = 5;
break;
case 4:
dir = 1;
break;
case 5:
dir = 0;
break;
case 6:
dir = 3;
break;
case 7:
dir = 2;
break;
}
}
switch (dir)
{
case L2R_U2D://从左到右,从上到下
regval |= (0 << 7) | (0 << 6) | (0 << 5);
break;
case L2R_D2U://从左到右,从下到上
regval |= (1 << 7) | (0 << 6) | (0 << 5);
break;
case R2L_U2D://从右到左,从上到下
regval |= (0 << 7) | (1 << 6) | (0 << 5);
break;
case R2L_D2U://从右到左,从下到上
regval |= (1 << 7) | (1 << 6) | (0 << 5);
break;
case U2D_L2R://从上到下,从左到右
regval |= (0 << 7) | (0 << 6) | (1 << 5);
break;
case U2D_R2L://从上到下,从右到左
regval |= (0 << 7) | (1 << 6) | (1 << 5);
break;
case D2U_L2R://从下到上,从左到右
regval |= (1 << 7) | (0 << 6) | (1 << 5);
break;
case D2U_R2L://从下到上,从右到左
regval |= (1 << 7) | (1 << 6) | (1 << 5);
break;
}
if (lcddev.id == 0X5510)dirreg = 0X3600;
else dirreg = 0X36;
if (lcddev.id == 0X9341 || lcddev.id == 0X7789) //9341 & 7789 要设置BGR位
{
regval |= 0X08;
}
LCD_WriteReg(dirreg, regval);
if (lcddev.id != 0X1963) //1963不做坐标处理
{
if (regval & 0X20)
{
if (lcddev.width < lcddev.height) //交换X,Y
{
temp = lcddev.width;
lcddev.width = lcddev.height;
lcddev.height = temp;
}
}
else
{
if (lcddev.width > lcddev.height) //交换X,Y
{
temp = lcddev.width;
lcddev.width = lcddev.height;
lcddev.height = temp;
}
}
}
//设置显示区域(开窗)大小
if (lcddev.id == 0X5510)
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(0);
LCD_WR_REG(lcddev.setxcmd + 1);
LCD_WR_DATA(0);
LCD_WR_REG(lcddev.setxcmd + 2);
LCD_WR_DATA((lcddev.width - 1) >> 8);
LCD_WR_REG(lcddev.setxcmd + 3);
LCD_WR_DATA((lcddev.width - 1) & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(0);
LCD_WR_REG(lcddev.setycmd + 1);
LCD_WR_DATA(0);
LCD_WR_REG(lcddev.setycmd + 2);
LCD_WR_DATA((lcddev.height - 1) >> 8);
LCD_WR_REG(lcddev.setycmd + 3);
LCD_WR_DATA((lcddev.height - 1) & 0XFF);
}
else
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(0);
LCD_WR_DATA(0);
LCD_WR_DATA((lcddev.width - 1) >> 8);
LCD_WR_DATA((lcddev.width - 1) & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(0);
LCD_WR_DATA(0);
LCD_WR_DATA((lcddev.height - 1) >> 8);
LCD_WR_DATA((lcddev.height - 1) & 0XFF);
}
}
//画点
//x,y:坐标
//POINT_COLOR:此点的颜色
void LCD_DrawPoint(uint16_t x,uint16_t y)
{
LCD_SetCursor(x,y); //设置光标位置
LCD_WriteRAM_Prepare(); //开始写入GRAM
LCD->LCD_RAM=POINT_COLOR;
}
//快速画点
//x,y:坐标
//color:颜色
void LCD_Fast_DrawPoint(uint16_t x,uint16_t y,uint32_t color)
{
if (lcddev.id == 0X5510)
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(x >> 8);
LCD_WR_REG(lcddev.setxcmd + 1);
LCD_WR_DATA(x & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(y >> 8);
LCD_WR_REG(lcddev.setycmd + 1);
LCD_WR_DATA(y & 0XFF);
}
else if (lcddev.id == 0X1963)
{
if (lcddev.dir == 0)x = lcddev.width - 1 - x;
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(x >> 8);
LCD_WR_DATA(x & 0XFF);
LCD_WR_DATA(x >> 8);
LCD_WR_DATA(x & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(y >> 8);
LCD_WR_DATA(y & 0XFF);
LCD_WR_DATA(y >> 8);
LCD_WR_DATA(y & 0XFF);
}
else //9341/5310/7789等设置坐标
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(x >> 8);
LCD_WR_DATA(x & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(y >> 8);
LCD_WR_DATA(y & 0XFF);
}
LCD->LCD_REG=lcddev.wramcmd;
LCD->LCD_RAM=color;
}
//SSD1963 背光设置
//pwm:背光等级,0~100.越大越亮.
void LCD_SSD_BackLightSet(uint8_t pwm)
{
LCD_WR_REG(0xBE); //配置PWM输出
LCD_WR_DATA(0x05); //1设置PWM频率
LCD_WR_DATA(pwm*2.55); //2设置PWM占空比
LCD_WR_DATA(0x01); //3设置C
LCD_WR_DATA(0xFF); //4设置D
LCD_WR_DATA(0x00); //5设置E
LCD_WR_DATA(0x00); //6设置F
}
//设置LCD显示方向
//dir:0,竖屏；1,横屏
void LCD_Display_Dir(uint8_t dir)
{
lcddev.dir = dir; //竖屏/横屏
if (dir == 0) //竖屏
{
lcddev.width = 240;
lcddev.height = 320;
if (lcddev.id == 0x5510)
{
lcddev.wramcmd = 0X2C00;
lcddev.setxcmd = 0X2A00;
lcddev.setycmd = 0X2B00;
lcddev.width = 480;
lcddev.height = 800;
}
else if (lcddev.id == 0X1963)
{
lcddev.wramcmd = 0X2C; //设置写入GRAM的指令
lcddev.setxcmd = 0X2B; //设置写X坐标指令
lcddev.setycmd = 0X2A; //设置写Y坐标指令
lcddev.width = 480; //设置宽度480
lcddev.height = 800; //设置高度800
}
else //其他IC, 包括: 9341 / 5310 / 7789等IC
{
lcddev.wramcmd = 0X2C;
lcddev.setxcmd = 0X2A;
lcddev.setycmd = 0X2B;
}
if (lcddev.id == 0X5310) //如果是5310 则表示是 320*480分辨率
{
lcddev.width = 320;
lcddev.height = 480;
}
}
else //横屏
{
lcddev.width = 320;
lcddev.height = 240;
if (lcddev.id == 0x5510)
{
lcddev.wramcmd = 0X2C00;
lcddev.setxcmd = 0X2A00;
lcddev.setycmd = 0X2B00;
lcddev.width = 800;
lcddev.height = 480;
}
else if (lcddev.id == 0X1963)
{
lcddev.wramcmd = 0X2C; //设置写入GRAM的指令
lcddev.setxcmd = 0X2A; //设置写X坐标指令
lcddev.setycmd = 0X2B; //设置写Y坐标指令
lcddev.width = 800; //设置宽度800
lcddev.height = 480; //设置高度480
}
else //其他IC, 包括: 9341 / 5310 / 7789等IC
{
lcddev.wramcmd = 0X2C;
lcddev.setxcmd = 0X2A;
lcddev.setycmd = 0X2B;
}
if (lcddev.id == 0X5310) //如果是5310 则表示是 320*480分辨率
{
lcddev.width = 480;
lcddev.height = 320;
}
}
LCD_Scan_Dir(DFT_SCAN_DIR); //默认扫描方向
}
//设置窗口,并自动设置画点坐标到窗口左上角(sx,sy).
//sx,sy:窗口起始坐标(左上角)
//width,height:窗口宽度和高度,必须大于0!!
//窗体大小:width*height.
void LCD_Set_Window(uint16_t sx, uint16_t sy, uint16_t width, uint16_t height)
{
uint16_t twidth, theight;
twidth = sx + width - 1;
theight = sy + height - 1;
if (lcddev.id == 0X1963 && lcddev.dir != 1) //1963竖屏特殊处理
{
sx = lcddev.width - width - sx;
height = sy + height - 1;
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(sx >> 8);
LCD_WR_DATA(sx & 0XFF);
LCD_WR_DATA((sx + width - 1) >> 8);
LCD_WR_DATA((sx + width - 1) & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(sy >> 8);
LCD_WR_DATA(sy & 0XFF);
LCD_WR_DATA(height >> 8);
LCD_WR_DATA(height & 0XFF);
}
else if (lcddev.id == 0X5510)
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(sx >> 8);
LCD_WR_REG(lcddev.setxcmd + 1);
LCD_WR_DATA(sx & 0XFF);
LCD_WR_REG(lcddev.setxcmd + 2);
LCD_WR_DATA(twidth >> 8);
LCD_WR_REG(lcddev.setxcmd + 3);
LCD_WR_DATA(twidth & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(sy >> 8);
LCD_WR_REG(lcddev.setycmd + 1);
LCD_WR_DATA(sy & 0XFF);
LCD_WR_REG(lcddev.setycmd + 2);
LCD_WR_DATA(theight >> 8);
LCD_WR_REG(lcddev.setycmd + 3);
LCD_WR_DATA(theight & 0XFF);
}
else //9341/5310/7789/1963横屏 等 设置窗口
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(sx >> 8);
LCD_WR_DATA(sx & 0XFF);
LCD_WR_DATA(twidth >> 8);
LCD_WR_DATA(twidth & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(sy >> 8);
LCD_WR_DATA(sy & 0XFF);
LCD_WR_DATA(theight >> 8);
LCD_WR_DATA(theight & 0XFF);
}
}
//初始化lcd
//该初始化函数可以初始化各种ILI93XX液晶,但是其他函数是基于ILI9320的!!!
//在其他型号的驱动芯片上没有测试!
void LCD_Init(void)
{
//尝试9341 ID的读取
LCD_WR_REG(0XD3);
lcddev.id=LCD_RD_DATA(); //dummy read
lcddev.id=LCD_RD_DATA(); //读到0X00
lcddev.id=LCD_RD_DATA(); //读取93
lcddev.id<<=8;
lcddev.id|=LCD_RD_DATA(); //读取41
if(lcddev.id!=0X9341) //非9341,尝试是不是7789
{
LCD_WR_REG(0X04);
lcddev.id = LCD_RD_DATA(); //dummy read
lcddev.id = LCD_RD_DATA(); //读到0X85
lcddev.id = LCD_RD_DATA(); //读取0X85
lcddev.id <<= 8;
lcddev.id |= LCD_RD_DATA(); //读取0X52
if (lcddev.id == 0X8552) //将8552的ID转换成7789
{
lcddev.id = 0x7789;
}
if (lcddev.id != 0x7789) //也不是ST7789, 尝试是不是 7789
{
LCD_WR_REG(0XD4);
lcddev.id=LCD_RD_DATA();//dummy read
lcddev.id=LCD_RD_DATA();//读回0X01
lcddev.id=LCD_RD_DATA();//读回0X53
lcddev.id<<=8;
lcddev.id|=LCD_RD_DATA(); //这里读回0X10
if(lcddev.id!=0X5310) //也不是NT35310,尝试看看是不是NT35510
{
LCD_WR_REG(0XDA00);
lcddev.id=LCD_RD_DATA(); //读回0X00
LCD_WR_REG(0XDB00);
lcddev.id=LCD_RD_DATA(); //读回0X80
lcddev.id<<=8;
LCD_WR_REG(0XDC00);
lcddev.id|=LCD_RD_DATA(); //读回0X00
if(lcddev.id==0x8000)lcddev.id=0x5510;//NT35510读回的ID是8000H,为方便区分,我们强制设置为5510
if(lcddev.id!=0X5510) //也不是NT5510,尝试看看是不是SSD1963
{
LCD_WR_REG(0XA1);
lcddev.id=LCD_RD_DATA();
lcddev.id=LCD_RD_DATA(); //读回0X57
lcddev.id<<=8;
lcddev.id|=LCD_RD_DATA(); //读回0X61
if(lcddev.id==0X5761)lcddev.id=0X1963;//SSD1963读回的ID是5761H,为方便区分,我们强制设置为1963
}
}
}
}
printf("LCD ID:%x\r\n",lcddev.id); //打印LCD ID
if(lcddev.id==0X9341) //9341初始化
{
LCD_WR_REG(0xCF);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC1);
LCD_WR_DATA(0X30);
LCD_WR_REG(0xED);
LCD_WR_DATA(0x64);
LCD_WR_DATA(0x03);
LCD_WR_DATA(0X12);
LCD_WR_DATA(0X81);
LCD_WR_REG(0xE8);
LCD_WR_DATA(0x85);
LCD_WR_DATA(0x10);
LCD_WR_DATA(0x7A);
LCD_WR_REG(0xCB);
LCD_WR_DATA(0x39);
LCD_WR_DATA(0x2C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x34);
LCD_WR_DATA(0x02);
LCD_WR_REG(0xF7);
LCD_WR_DATA(0x20);
LCD_WR_REG(0xEA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC0); //Power control
LCD_WR_DATA(0x1B); //VRH[5:0]
LCD_WR_REG(0xC1); //Power control
LCD_WR_DATA(0x01); //SAP[2:0];BT[3:0]
LCD_WR_REG(0xC5); //VCM control
LCD_WR_DATA(0x30); //3F
LCD_WR_DATA(0x30); //3C
LCD_WR_REG(0xC7); //VCM control2
LCD_WR_DATA(0XB7);
LCD_WR_REG(0x36); // Memory Access Control
LCD_WR_DATA(0x48);
LCD_WR_REG(0x3A);
LCD_WR_DATA(0x55);
LCD_WR_REG(0xB1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1A);
LCD_WR_REG(0xB6); // Display Function Control
LCD_WR_DATA(0x0A);
LCD_WR_DATA(0xA2);
LCD_WR_REG(0xF2); // 3Gamma Function Disable
LCD_WR_DATA(0x00);
LCD_WR_REG(0x26); //Gamma curve selected
LCD_WR_DATA(0x01);
LCD_WR_REG(0xE0); //Set Gamma
LCD_WR_DATA(0x0F);
LCD_WR_DATA(0x2A);
LCD_WR_DATA(0x28);
LCD_WR_DATA(0x08);
LCD_WR_DATA(0x0E);
LCD_WR_DATA(0x08);
LCD_WR_DATA(0x54);
LCD_WR_DATA(0XA9);
LCD_WR_DATA(0x43);
LCD_WR_DATA(0x0A);
LCD_WR_DATA(0x0F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0XE1); //Set Gamma
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x15);
LCD_WR_DATA(0x17);
LCD_WR_DATA(0x07);
LCD_WR_DATA(0x11);
LCD_WR_DATA(0x06);
LCD_WR_DATA(0x2B);
LCD_WR_DATA(0x56);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x05);
LCD_WR_DATA(0x10);
LCD_WR_DATA(0x0F);
LCD_WR_DATA(0x3F);
LCD_WR_DATA(0x3F);
LCD_WR_DATA(0x0F);
LCD_WR_REG(0x2B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x3f);
LCD_WR_REG(0x2A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xef);
LCD_WR_REG(0x11); //Exit Sleep
HAL_Delay(120);
LCD_WR_REG(0x29); //display on
}
else if(lcddev.id==0x7789) //7789初始化
{
LCD_WR_REG(0x11);
HAL_Delay(120);
LCD_WR_REG(0x36);
LCD_WR_DATA(0x00);
LCD_WR_REG(0x3A);
LCD_WR_DATA(0X05);
LCD_WR_REG(0xB2);
LCD_WR_DATA(0x0C);
LCD_WR_DATA(0x0C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x33);
LCD_WR_DATA(0x33);
LCD_WR_REG(0xB7);
LCD_WR_DATA(0x35);
LCD_WR_REG(0xBB); //vcom
LCD_WR_DATA(0x32); //30
LCD_WR_REG(0xC0);
LCD_WR_DATA(0x0C);
LCD_WR_REG(0xC2);
LCD_WR_DATA(0x01);
LCD_WR_REG(0xC3); //vrh
LCD_WR_DATA(0x10); //17 0D
LCD_WR_REG(0xC4); //vdv
LCD_WR_DATA(0x20); //20
LCD_WR_REG(0xC6);
LCD_WR_DATA(0x0f);
LCD_WR_REG(0xD0);
LCD_WR_DATA(0xA4);
LCD_WR_DATA(0xA1);
LCD_WR_REG(0xE0); //Set Gamma
LCD_WR_DATA(0xd0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x07);
LCD_WR_DATA(0x0a);
LCD_WR_DATA(0x28);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0X44);
LCD_WR_DATA(0x42);
LCD_WR_DATA(0x06);
LCD_WR_DATA(0x0e);
LCD_WR_DATA(0x12);
LCD_WR_DATA(0x14);
LCD_WR_DATA(0x17);
LCD_WR_REG(0XE1); //Set Gamma
LCD_WR_DATA(0xd0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x07);
LCD_WR_DATA(0x0a);
LCD_WR_DATA(0x28);
LCD_WR_DATA(0x31);
LCD_WR_DATA(0x54);
LCD_WR_DATA(0x47);
LCD_WR_DATA(0x0e);
LCD_WR_DATA(0x1c);
LCD_WR_DATA(0x17);
LCD_WR_DATA(0x1b);
LCD_WR_DATA(0x1e);
LCD_WR_REG(0x2A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xef);
LCD_WR_REG(0x2B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x3f);
LCD_WR_REG(0x29); //display on
}
else if(lcddev.id==0x5310)
{
LCD_WR_REG(0xED);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0xFE);
LCD_WR_REG(0xEE);
LCD_WR_DATA(0xDE);
LCD_WR_DATA(0x21);
LCD_WR_REG(0xF1);
LCD_WR_DATA(0x01);
LCD_WR_REG(0xDF);
LCD_WR_DATA(0x10);
//VCOMvoltage//
LCD_WR_REG(0xC4);
LCD_WR_DATA(0x8F); //5f
LCD_WR_REG(0xC6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xE2);
LCD_WR_DATA(0xE2);
LCD_WR_DATA(0xE2);
LCD_WR_REG(0xBF);
LCD_WR_DATA(0xAA);
LCD_WR_REG(0xB0);
LCD_WR_DATA(0x0D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x0D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x11);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x19);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x21);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5D);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB1);
LCD_WR_DATA(0x80);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x8B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x96);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x03);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB4);
LCD_WR_DATA(0x8B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x96);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA1);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB5);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x03);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x04);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5E);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x64);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x8C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xAC);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDC);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x70);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x90);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xEB);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDC);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xBA);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC1);
LCD_WR_DATA(0x20);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x54);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xFF);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC2);
LCD_WR_DATA(0x0A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x04);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC3);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x39);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x37);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x36);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x29);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x26);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x23);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x36);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x29);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x26);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x23);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC4);
LCD_WR_DATA(0x62);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x05);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x84);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x18);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x18);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x50);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x0C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x17);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x95);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xE6);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC5);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x65);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x76);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC6);
LCD_WR_DATA(0x20);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x17);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC9);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE0);
LCD_WR_DATA(0x16);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x21);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x36);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x46);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x52);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x64);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x7A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x8B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB9);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xCA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD9);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xE0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE1);
LCD_WR_DATA(0x16);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x22);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x36);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x45);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x52);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x64);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x7A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x8B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB9);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xCA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xE0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE2);
LCD_WR_DATA(0x05);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x0B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x34);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x4F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x61);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x79);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x97);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE3);
LCD_WR_DATA(0x05);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x33);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x50);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x62);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x78);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x97);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD5);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE4);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x4B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x74);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x84);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x93);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBE);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xCD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE5);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x29);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x4B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x74);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x84);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x93);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBE);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xCD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDC);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE6);
LCD_WR_DATA(0x11);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x34);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x56);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x76);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x77);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBB);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x45);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x43);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE7);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x76);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x67);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x67);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x87);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBB);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x77);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x56);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x23);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x33);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x45);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x87);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x77);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xAA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBB);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE9);
LCD_WR_DATA(0xAA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0x00);
LCD_WR_DATA(0xAA);
LCD_WR_REG(0xCF);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xF0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x50);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xF9);
LCD_WR_DATA(0x06);
LCD_WR_DATA(0x10);
LCD_WR_DATA(0x29);
LCD_WR_DATA(0x00);
LCD_WR_REG(0x3A);
LCD_WR_DATA(0x55); //66
LCD_WR_REG(0x11);
HAL_Delay(100);
LCD_WR_REG(0x29);
LCD_WR_REG(0x35);
LCD_WR_DATA(0x00);
LCD_WR_REG(0x51);
LCD_WR_DATA(0xFF);
LCD_WR_REG(0x53);
LCD_WR_DATA(0x2C);
LCD_WR_REG(0x55);
LCD_WR_DATA(0x82);
LCD_WR_REG(0x2c);
}
else if(lcddev.id==0x5510)
{
LCD_WriteReg(0xF000,0x55);
LCD_WriteReg(0xF001,0xAA);
LCD_WriteReg(0xF002,0x52);
LCD_WriteReg(0xF003,0x08);
LCD_WriteReg(0xF004,0x01);
//AVDD Set AVDD 5.2V
LCD_WriteReg(0xB000,0x0D);
LCD_WriteReg(0xB001,0x0D);
LCD_WriteReg(0xB002,0x0D);
//AVDD ratio
LCD_WriteReg(0xB600,0x34);
LCD_WriteReg(0xB601,0x34);
LCD_WriteReg(0xB602,0x34);
//AVEE -5.2V
LCD_WriteReg(0xB100,0x0D);
LCD_WriteReg(0xB101,0x0D);
LCD_WriteReg(0xB102,0x0D);
//AVEE ratio
LCD_WriteReg(0xB700,0x34);
LCD_WriteReg(0xB701,0x34);
LCD_WriteReg(0xB702,0x34);
//VCL -2.5V
LCD_WriteReg(0xB200,0x00);
LCD_WriteReg(0xB201,0x00);
LCD_WriteReg(0xB202,0x00);
//VCL ratio
LCD_WriteReg(0xB800,0x24);
LCD_WriteReg(0xB801,0x24);
LCD_WriteReg(0xB802,0x24);
//VGH 15V (Free pump)
LCD_WriteReg(0xBF00,0x01);
LCD_WriteReg(0xB300,0x0F);
LCD_WriteReg(0xB301,0x0F);
LCD_WriteReg(0xB302,0x0F);
//VGH ratio
LCD_WriteReg(0xB900,0x34);
LCD_WriteReg(0xB901,0x34);
LCD_WriteReg(0xB902,0x34);
//VGL_REG -10V
LCD_WriteReg(0xB500,0x08);
LCD_WriteReg(0xB501,0x08);
LCD_WriteReg(0xB502,0x08);
LCD_WriteReg(0xC200,0x03);
//VGLX ratio
LCD_WriteReg(0xBA00,0x24);
LCD_WriteReg(0xBA01,0x24);
LCD_WriteReg(0xBA02,0x24);
//VGMP/VGSP 4.5V/0V
LCD_WriteReg(0xBC00,0x00);
LCD_WriteReg(0xBC01,0x78);
LCD_WriteReg(0xBC02,0x00);
//VGMN/VGSN -4.5V/0V
LCD_WriteReg(0xBD00,0x00);
LCD_WriteReg(0xBD01,0x78);
LCD_WriteReg(0xBD02,0x00);
//VCOM
LCD_WriteReg(0xBE00,0x00);
LCD_WriteReg(0xBE01,0x64);
//Gamma Setting
LCD_WriteReg(0xD100,0x00);
LCD_WriteReg(0xD101,0x33);
LCD_WriteReg(0xD102,0x00);
LCD_WriteReg(0xD103,0x34);
LCD_WriteReg(0xD104,0x00);
LCD_WriteReg(0xD105,0x3A);
LCD_WriteReg(0xD106,0x00);
LCD_WriteReg(0xD107,0x4A);
LCD_WriteReg(0xD108,0x00);
LCD_WriteReg(0xD109,0x5C);
LCD_WriteReg(0xD10A,0x00);
LCD_WriteReg(0xD10B,0x81);
LCD_WriteReg(0xD10C,0x00);
LCD_WriteReg(0xD10D,0xA6);
LCD_WriteReg(0xD10E,0x00);
LCD_WriteReg(0xD10F,0xE5);
LCD_WriteReg(0xD110,0x01);
LCD_WriteReg(0xD666666,0x13);
LCD_WriteReg(0xD112,0x01);
LCD_WriteReg(0xD113,0x54);
LCD_WriteReg(0xD114,0x01);
LCD_WriteReg(0xD115,0x82);
LCD_WriteReg(0xD116,0x01);
LCD_WriteReg(0xD117,0xCA);
LCD_WriteReg(0xD118,0x02);
LCD_WriteReg(0xD119,0x00);
LCD_WriteReg(0xD11A,0x02);
LCD_WriteReg(0xD11B,0x01);
LCD_WriteReg(0xD11C,0x02);
LCD_WriteReg(0xD11D,0x34);
LCD_WriteReg(0xD11E,0x02);
LCD_WriteReg(0xD11F,0x67);
LCD_WriteReg(0xD120,0x02);
LCD_WriteReg(0xD121,0x84);
LCD_WriteReg(0xD122,0x02);
LCD_WriteReg(0xD123,0xA4);
LCD_WriteReg(0xD124,0x02);
LCD_WriteReg(0xD125,0xB7);
LCD_WriteReg(0xD126,0x02);
LCD_WriteReg(0xD127,0xCF);
LCD_WriteReg(0xD128,0x02);
LCD_WriteReg(0xD129,0xDE);
LCD_WriteReg(0xD12A,0x02);
LCD_WriteReg(0xD12B,0xF2);
LCD_WriteReg(0xD12C,0x02);
LCD_WriteReg(0xD12D,0xFE);
LCD_WriteReg(0xD12E,0x03);
LCD_WriteReg(0xD12F,0x10);
LCD_WriteReg(0xD130,0x03);
LCD_WriteReg(0xD131,0x33);
LCD_WriteReg(0xD132,0x03);
LCD_WriteReg(0xD133,0x6D);
LCD_WriteReg(0xD200,0x00);
LCD_WriteReg(0xD201,0x33);
LCD_WriteReg(0xD202,0x00);
LCD_WriteReg(0xD203,0x34);
LCD_WriteReg(0xD204,0x00);
LCD_WriteReg(0xD205,0x3A);
LCD_WriteReg(0xD206,0x00);
LCD_WriteReg(0xD207,0x4A);
LCD_WriteReg(0xD208,0x00);
LCD_WriteReg(0xD209,0x5C);
LCD_WriteReg(0xD20A,0x00);
LCD_WriteReg(0xD20B,0x81);
LCD_WriteReg(0xD20C,0x00);
LCD_WriteReg(0xD20D,0xA6);
LCD_WriteReg(0xD20E,0x00);
LCD_WriteReg(0xD20F,0xE5);
LCD_WriteReg(0xD210,0x01);
LCD_WriteReg(0xD211,0x13);
LCD_WriteReg(0xD212,0x01);
LCD_WriteReg(0xD213,0x54);
LCD_WriteReg(0xD214,0x01);
LCD_WriteReg(0xD215,0x82);
LCD_WriteReg(0xD216,0x01);
LCD_WriteReg(0xD217,0xCA);
LCD_WriteReg(0xD218,0x02);
LCD_WriteReg(0xD219,0x00);
LCD_WriteReg(0xD21A,0x02);
LCD_WriteReg(0xD21B,0x01);
LCD_WriteReg(0xD21C,0x02);
LCD_WriteReg(0xD21D,0x34);
LCD_WriteReg(0xD21E,0x02);
LCD_WriteReg(0xD21F,0x67);
LCD_WriteReg(0xD220,0x02);
LCD_WriteReg(0xD221,0x84);
LCD_WriteReg(0xD222,0x02);
LCD_WriteReg(0xD223,0xA4);
LCD_WriteReg(0xD224,0x02);
LCD_WriteReg(0xD225,0xB7);
LCD_WriteReg(0xD226,0x02);
LCD_WriteReg(0xD227,0xCF);
LCD_WriteReg(0xD228,0x02);
LCD_WriteReg(0xD229,0xDE);
LCD_WriteReg(0xD22A,0x02);
LCD_WriteReg(0xD22B,0xF2);
LCD_WriteReg(0xD22C,0x02);
LCD_WriteReg(0xD22D,0xFE);
LCD_WriteReg(0xD22E,0x03);
LCD_WriteReg(0xD22F,0x10);
LCD_WriteReg(0xD230,0x03);
LCD_WriteReg(0xD231,0x33);
LCD_WriteReg(0xD232,0x03);
LCD_WriteReg(0xD233,0x6D);
LCD_WriteReg(0xD300,0x00);
LCD_WriteReg(0xD301,0x33);
LCD_WriteReg(0xD302,0x00);
LCD_WriteReg(0xD303,0x34);
LCD_WriteReg(0xD304,0x00);
LCD_WriteReg(0xD305,0x3A);
LCD_WriteReg(0xD306,0x00);
LCD_WriteReg(0xD307,0x4A);
LCD_WriteReg(0xD308,0x00);
LCD_WriteReg(0xD309,0x5C);
LCD_WriteReg(0xD30A,0x00);
LCD_WriteReg(0xD30B,0x81);
LCD_WriteReg(0xD30C,0x00);
LCD_WriteReg(0xD30D,0xA6);
LCD_WriteReg(0xD30E,0x00);
LCD_WriteReg(0xD30F,0xE5);
LCD_WriteReg(0xD310,0x01);
LCD_WriteReg(0xD311,0x13);
LCD_WriteReg(0xD312,0x01);
LCD_WriteReg(0xD313,0x54);
LCD_WriteReg(0xD314,0x01);
LCD_WriteReg(0xD315,0x82);
LCD_WriteReg(0xD316,0x01);
LCD_WriteReg(0xD317,0xCA);
LCD_WriteReg(0xD318,0x02);
LCD_WriteReg(0xD319,0x00);
LCD_WriteReg(0xD31A,0x02);
LCD_WriteReg(0xD31B,0x01);
LCD_WriteReg(0xD31C,0x02);
LCD_WriteReg(0xD31D,0x34);
LCD_WriteReg(0xD31E,0x02);
LCD_WriteReg(0xD31F,0x67);
LCD_WriteReg(0xD320,0x02);
LCD_WriteReg(0xD321,0x84);
LCD_WriteReg(0xD322,0x02);
LCD_WriteReg(0xD323,0xA4);
LCD_WriteReg(0xD324,0x02);
LCD_WriteReg(0xD325,0xB7);
LCD_WriteReg(0xD326,0x02);
LCD_WriteReg(0xD327,0xCF);
LCD_WriteReg(0xD328,0x02);
LCD_WriteReg(0xD329,0xDE);
LCD_WriteReg(0xD32A,0x02);
LCD_WriteReg(0xD32B,0xF2);
LCD_WriteReg(0xD32C,0x02);
LCD_WriteReg(0xD32D,0xFE);
LCD_WriteReg(0xD32E,0x03);
LCD_WriteReg(0xD32F,0x10);
LCD_WriteReg(0xD330,0x03);
LCD_WriteReg(0xD331,0x33);
LCD_WriteReg(0xD332,0x03);
LCD_WriteReg(0xD333,0x6D);
LCD_WriteReg(0xD400,0x00);
LCD_WriteReg(0xD401,0x33);
LCD_WriteReg(0xD402,0x00);
LCD_WriteReg(0xD403,0x34);
LCD_WriteReg(0xD404,0x00);
LCD_WriteReg(0xD405,0x3A);
LCD_WriteReg(0xD406,0x00);
LCD_WriteReg(0xD407,0x4A);
LCD_WriteReg(0xD408,0x00);
LCD_WriteReg(0xD409,0x5C);
LCD_WriteReg(0xD40A,0x00);
LCD_WriteReg(0xD40B,0x81);
LCD_WriteReg(0xD40C,0x00);
LCD_WriteReg(0xD40D,0xA6);
LCD_WriteReg(0xD40E,0x00);
LCD_WriteReg(0xD40F,0xE5);
LCD_WriteReg(0xD410,0x01);
LCD_WriteReg(0xD411,0x13);
LCD_WriteReg(0xD412,0x01);
LCD_WriteReg(0xD413,0x54);
LCD_WriteReg(0xD414,0x01);
LCD_WriteReg(0xD415,0x82);
LCD_WriteReg(0xD416,0x01);
LCD_WriteReg(0xD417,0xCA);
LCD_WriteReg(0xD418,0x02);
LCD_WriteReg(0xD419,0x00);
LCD_WriteReg(0xD41A,0x02);
LCD_WriteReg(0xD41B,0x01);
LCD_WriteReg(0xD41C,0x02);
LCD_WriteReg(0xD41D,0x34);
LCD_WriteReg(0xD41E,0x02);
LCD_WriteReg(0xD41F,0x67);
LCD_WriteReg(0xD420,0x02);
LCD_WriteReg(0xD421,0x84);
LCD_WriteReg(0xD422,0x02);
LCD_WriteReg(0xD423,0xA4);
LCD_WriteReg(0xD424,0x02);
LCD_WriteReg(0xD425,0xB7);
LCD_WriteReg(0xD426,0x02);
LCD_WriteReg(0xD427,0xCF);
LCD_WriteReg(0xD428,0x02);
LCD_WriteReg(0xD429,0xDE);
LCD_WriteReg(0xD42A,0x02);
LCD_WriteReg(0xD42B,0xF2);
LCD_WriteReg(0xD42C,0x02);
LCD_WriteReg(0xD42D,0xFE);
LCD_WriteReg(0xD42E,0x03);
LCD_WriteReg(0xD42F,0x10);
LCD_WriteReg(0xD430,0x03);
LCD_WriteReg(0xD431,0x33);
LCD_WriteReg(0xD432,0x03);
LCD_WriteReg(0xD433,0x6D);
LCD_WriteReg(0xD500,0x00);
LCD_WriteReg(0xD501,0x33);
LCD_WriteReg(0xD502,0x00);
LCD_WriteReg(0xD503,0x34);
LCD_WriteReg(0xD504,0x00);
LCD_WriteReg(0xD505,0x3A);
LCD_WriteReg(0xD506,0x00);
LCD_WriteReg(0xD507,0x4A);
LCD_WriteReg(0xD508,0x00);
LCD_WriteReg(0xD509,0x5C);
LCD_WriteReg(0xD50A,0x00);
LCD_WriteReg(0xD50B,0x81);
LCD_WriteReg(0xD50C,0x00);
LCD_WriteReg(0xD50D,0xA6);
LCD_WriteReg(0xD50E,0x00);
LCD_WriteReg(0xD50F,0xE5);
LCD_WriteReg(0xD510,0x01);
LCD_WriteReg(0xD511,0x13);
LCD_WriteReg(0xD512,0x01);
LCD_WriteReg(0xD513,0x54);
LCD_WriteReg(0xD514,0x01);
LCD_WriteReg(0xD515,0x82);
LCD_WriteReg(0xD516,0x01);
LCD_WriteReg(0xD517,0xCA);
LCD_WriteReg(0xD518,0x02);
LCD_WriteReg(0xD519,0x00);
LCD_WriteReg(0xD51A,0x02);
LCD_WriteReg(0xD51B,0x01);
LCD_WriteReg(0xD51C,0x02);
LCD_WriteReg(0xD51D,0x34);
LCD_WriteReg(0xD51E,0x02);
LCD_WriteReg(0xD51F,0x67);
LCD_WriteReg(0xD520,0x02);
LCD_WriteReg(0xD521,0x84);
LCD_WriteReg(0xD522,0x02);
LCD_WriteReg(0xD523,0xA4);
LCD_WriteReg(0xD524,0x02);
LCD_WriteReg(0xD525,0xB7);
LCD_WriteReg(0xD526,0x02);
LCD_WriteReg(0xD527,0xCF);
LCD_WriteReg(0xD528,0x02);
LCD_WriteReg(0xD529,0xDE);
LCD_WriteReg(0xD52A,0x02);
LCD_WriteReg(0xD52B,0xF2);
LCD_WriteReg(0xD52C,0x02);
LCD_WriteReg(0xD52D,0xFE);
LCD_WriteReg(0xD52E,0x03);
LCD_WriteReg(0xD52F,0x10);
LCD_WriteReg(0xD530,0x03);
LCD_WriteReg(0xD531,0x33);
LCD_WriteReg(0xD532,0x03);
LCD_WriteReg(0xD533,0x6D);
LCD_WriteReg(0xD600,0x00);
LCD_WriteReg(0xD601,0x33);
LCD_WriteReg(0xD602,0x00);
LCD_WriteReg(0xD603,0x34);
LCD_WriteReg(0xD604,0x00);
LCD_WriteReg(0xD605,0x3A);
LCD_WriteReg(0xD606,0x00);
LCD_WriteReg(0xD607,0x4A);
LCD_WriteReg(0xD608,0x00);
LCD_WriteReg(0xD609,0x5C);
LCD_WriteReg(0xD60A,0x00);
LCD_WriteReg(0xD60B,0x81);
LCD_WriteReg(0xD60C,0x00);
LCD_WriteReg(0xD60D,0xA6);
LCD_WriteReg(0xD60E,0x00);
LCD_WriteReg(0xD60F,0xE5);
LCD_WriteReg(0xD610,0x01);
LCD_WriteReg(0xD611,0x13);
LCD_WriteReg(0xD612,0x01);
LCD_WriteReg(0xD613,0x54);
LCD_WriteReg(0xD614,0x01);
LCD_WriteReg(0xD615,0x82);
LCD_WriteReg(0xD616,0x01);
LCD_WriteReg(0xD617,0xCA);
LCD_WriteReg(0xD618,0x02);
LCD_WriteReg(0xD619,0x00);
LCD_WriteReg(0xD61A,0x02);
LCD_WriteReg(0xD61B,0x01);
LCD_WriteReg(0xD61C,0x02);
LCD_WriteReg(0xD61D,0x34);
LCD_WriteReg(0xD61E,0x02);
LCD_WriteReg(0xD61F,0x67);
LCD_WriteReg(0xD620,0x02);
LCD_WriteReg(0xD621,0x84);
LCD_WriteReg(0xD622,0x02);
LCD_WriteReg(0xD623,0xA4);
LCD_WriteReg(0xD624,0x02);
LCD_WriteReg(0xD625,0xB7);
LCD_WriteReg(0xD626,0x02);
LCD_WriteReg(0xD627,0xCF);
LCD_WriteReg(0xD628,0x02);
LCD_WriteReg(0xD629,0xDE);
LCD_WriteReg(0xD62A,0x02);
LCD_WriteReg(0xD62B,0xF2);
LCD_WriteReg(0xD62C,0x02);
LCD_WriteReg(0xD62D,0xFE);
LCD_WriteReg(0xD62E,0x03);
LCD_WriteReg(0xD62F,0x10);
LCD_WriteReg(0xD630,0x03);
LCD_WriteReg(0xD631,0x33);
LCD_WriteReg(0xD632,0x03);
LCD_WriteReg(0xD633,0x6D);
//LV2 Page 0 enable
LCD_WriteReg(0xF000,0x55);
LCD_WriteReg(0xF001,0xAA);
LCD_WriteReg(0xF002,0x52);
LCD_WriteReg(0xF003,0x08);
LCD_WriteReg(0xF004,0x00);
//Display control
LCD_WriteReg(0xB100, 0xCC);
LCD_WriteReg(0xB101, 0x00);
//Source hold time
LCD_WriteReg(0xB600,0x05);
//Gate EQ control
LCD_WriteReg(0xB700,0x70);
LCD_WriteReg(0xB701,0x70);
//Source EQ control (Mode 2)
LCD_WriteReg(0xB800,0x01);
LCD_WriteReg(0xB801,0x03);
LCD_WriteReg(0xB802,0x03);
LCD_WriteReg(0xB803,0x03);
//Inversion mode (2-dot)
LCD_WriteReg(0xBC00,0x02);
LCD_WriteReg(0xBC01,0x00);
LCD_WriteReg(0xBC02,0x00);
//Timing control 4H w/ 4-delay
LCD_WriteReg(0xC900,0xD0);
LCD_WriteReg(0xC901,0x02);
LCD_WriteReg(0xC902,0x50);
LCD_WriteReg(0xC903,0x50);
LCD_WriteReg(0xC904,0x50);
LCD_WriteReg(0x3500,0x00);
LCD_WriteReg(0x3A00,0x55); //16-bit/pixel
LCD_WR_REG(0x1100);
delay_us(120);
LCD_WR_REG(0x2900);
}
else if(lcddev.id==0X1963)
{
LCD_WR_REG(0xE2); //Set PLL with OSC = 10MHz (hardware), Multiplier N = 35, 250MHz < VCO < 800MHz = OSC*(N+1), VCO = 300MHz
LCD_WR_DATA(0x1D); //参数1
LCD_WR_DATA(0x02); //参数2 Divider M = 2, PLL = 300/(M+1) = 100MHz
LCD_WR_DATA(0x04); //参数3 Validate M and N values
delay_us(100);
LCD_WR_REG(0xE0); // Start PLL command
LCD_WR_DATA(0x01); // enable PLL
HAL_Delay(10);
LCD_WR_REG(0xE0); // Start PLL command again
LCD_WR_DATA(0x03); // now, use PLL output as system clock
HAL_Delay(12);
LCD_WR_REG(0x01); //软复位
HAL_Delay(10);
LCD_WR_REG(0xE6); //设置像素频率,33Mhz
LCD_WR_DATA(0x2F);
LCD_WR_DATA(0xFF);
LCD_WR_DATA(0xFF);
LCD_WR_REG(0xB0); //设置LCD模式
LCD_WR_DATA(0x20); //24位模式
LCD_WR_DATA(0x00); //TFT 模式
LCD_WR_DATA((SSD_HOR_RESOLUTION-1)>>8);//设置LCD水平像素
LCD_WR_DATA(SSD_HOR_RESOLUTION-1);
LCD_WR_DATA((SSD_VER_RESOLUTION-1)>>8);//设置LCD垂直像素
LCD_WR_DATA(SSD_VER_RESOLUTION-1);
LCD_WR_DATA(0x00); //RGB序列
LCD_WR_REG(0xB4); //Set horizontal period
LCD_WR_DATA((SSD_HT-1)>>8);
LCD_WR_DATA(SSD_HT-1);
LCD_WR_DATA(SSD_HPS>>8);
LCD_WR_DATA(SSD_HPS);
LCD_WR_DATA(SSD_HOR_PULSE_WIDTH-1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB6); //Set vertical period
LCD_WR_DATA((SSD_VT-1)>>8);
LCD_WR_DATA(SSD_VT-1);
LCD_WR_DATA(SSD_VPS>>8);
LCD_WR_DATA(SSD_VPS);
LCD_WR_DATA(SSD_VER_FRONT_PORCH-1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xF0); //设置SSD1963与CPU接口为16bit
LCD_WR_DATA(0x03); //16-bit(565 format) data for 16bpp
LCD_WR_REG(0x29); //开启显示
//设置PWM输出 背光通过占空比可调
LCD_WR_REG(0xD0); //设置自动白平衡DBC
LCD_WR_DATA(0x00); //disable
LCD_WR_REG(0xBE); //配置PWM输出
LCD_WR_DATA(0x05); //1设置PWM频率
LCD_WR_DATA(0xFE); //2设置PWM占空比
LCD_WR_DATA(0x01); //3设置C
LCD_WR_DATA(0x00); //4设置D
LCD_WR_DATA(0x00); //5设置E
LCD_WR_DATA(0x00); //6设置F
LCD_WR_REG(0xB8); //设置GPIO配置
LCD_WR_DATA(0x03); //2个IO口设置成输出
LCD_WR_DATA(0x01); //GPIO使用正常的IO功能
LCD_WR_REG(0xBA);
LCD_WR_DATA(0X01); //GPIO[1:0]=01,控制LCD方向
LCD_SSD_BackLightSet(100);//背光设置为最亮
}
//初始化完成以后,提速
if(lcddev.id==0X9341||lcddev.id==0X5310||lcddev.id==0X5510||lcddev.id==0X1963)//如果是这几个IC,则设置WR时序为最快
{
//重新配置写时序控制寄存器的时序
FSMC_Bank1E->BWTR[6]&=~(0XF<<0);//地址建立时间(ADDSET)清零
FSMC_Bank1E->BWTR[6]&=~(0XF<<8);//数据保存时间清零
FSMC_Bank1E->BWTR[6]|=3<<0; //地址建立时间(ADDSET)为3个HCLK =18ns
FSMC_Bank1E->BWTR[6]|=2<<8; //数据保存时间(DATAST)为6ns*3个HCLK=18ns
}
LCD_Display_Dir(0); //默认为竖屏
HAL_GPIO_WritePin(LCD_BLK_GPIO_Port, LCD_BLK_Pin, GPIO_PIN_SET); //点亮背光
LCD_Clear(WHITE);
}
//清屏函数
//color:要清屏的填充色
void LCD_Clear(uint32_t color)
{
uint32_t index=0;
uint32_t totalpoint=lcddev.width;
totalpoint*=lcddev.height; //得到总点数
LCD_SetCursor(0x00,0x0000); //设置光标位置
LCD_WriteRAM_Prepare(); //开始写入GRAM
for(index=0; index<totalpoint; index++)
{
LCD->LCD_RAM=color;
}
}
//在指定区域内填充单个颜色
//(sx,sy),(ex,ey):填充矩形对角坐标,区域大小为:(ex-sx+1)*(ey-sy+1)
//color:要填充的颜色
void LCD_Fill(uint16_t sx,uint16_t sy,uint16_t ex,uint16_t ey,uint32_t color)
{
uint16_t i,j;
uint16_t xlen=0;
xlen=ex-sx+1;
for(i=sy; i<=ey; i++)
{
LCD_SetCursor(sx,i); //设置光标位置
LCD_WriteRAM_Prepare(); //开始写入GRAM
for (j = 0; j < xlen; j++)
{
LCD->LCD_RAM=color; //设置光标位置
}
}
}
//在指定区域内填充指定颜色块
//(sx,sy),(ex,ey):填充矩形对角坐标,区域大小为:(ex-sx+1)*(ey-sy+1)
//color:要填充的颜色
void LCD_Color_Fill(uint16_t sx,uint16_t sy,uint16_t ex,uint16_t ey,uint16_t *color)
{
uint16_t height,width;
uint16_t i,j;
width=ex-sx+1; //得到填充的宽度
height=ey-sy+1; //高度
for(i=0; i<height; i++)
{
LCD_SetCursor(sx,sy+i); //设置光标位置
LCD_WriteRAM_Prepare(); //开始写入GRAM
for (j = 0; j < width; j++)
{
LCD->LCD_RAM=color[i * width + j]; //写入数据
}
}
}
//画线
//x1,y1:起点坐标
//x2,y2:终点坐标
void LCD_DrawLine(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2)
{
uint16_t t;
int xerr = 0, yerr = 0, delta_x, delta_y, distance;
int incx, incy, uRow, uCol;
delta_x = x2 - x1; //计算坐标增量
delta_y = y2 - y1;
uRow = x1;
uCol = y1;
if (delta_x > 0)incx = 1; //设置单步方向
else if (delta_x == 0)incx = 0; //垂直线
else
{
incx = -1;
delta_x = -delta_x;
}
if (delta_y > 0)incy = 1;
else if (delta_y == 0)incy = 0; //水平线
else
{
incy = -1;
delta_y = -delta_y;
}
if ( delta_x > delta_y)distance = delta_x; //选取基本增量坐标轴
else distance = delta_y;
for (t = 0; t <= distance + 1; t++ ) //画线输出
{
LCD_DrawPoint(uRow, uCol); //画点
xerr += delta_x ;
yerr += delta_y ;
if (xerr > distance)
{
xerr -= distance;
uRow += incx;
}
if (yerr > distance)
{
yerr -= distance;
uCol += incy;
}
}
}
//画矩形
//(x1,y1),(x2,y2):矩形的对角坐标
void LCD_DrawRectangle(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2)
{
LCD_DrawLine(x1,y1,x2,y1);
LCD_DrawLine(x1,y1,x1,y2);
LCD_DrawLine(x1,y2,x2,y2);
LCD_DrawLine(x2,y1,x2,y2);
}
//在指定位置画一个指定大小的圆
//(x,y):中心点
//r :半径
void LCD_Draw_Circle(uint16_t x0,uint16_t y0,uint8_t r)
{
int a, b;
int di;
a = 0;
b = r;
di = 3 - (r << 1); //判断下个点位置的标志
while (a <= b)
{
LCD_DrawPoint(x0 + a, y0 - b); //5
LCD_DrawPoint(x0 + b, y0 - a); //0
LCD_DrawPoint(x0 + b, y0 + a); //4
LCD_DrawPoint(x0 + a, y0 + b); //6
LCD_DrawPoint(x0 - a, y0 + b); //1
LCD_DrawPoint(x0 - b, y0 + a);
LCD_DrawPoint(x0 - a, y0 - b); //2
LCD_DrawPoint(x0 - b, y0 - a); //7
a++;
//使用Bresenham算法画圆
if (di < 0)di += 4 * a + 6;
else
{
di += 10 + 4 * (a - b);
b--;
}
}
}
//在指定位置显示一个字符
//x,y:起始坐标
//num:要显示的字符:" "--->"~"
//size:字体大小 12/16/24/32
//mode:叠加方式(1)还是非叠加方式(0)
void LCD_ShowChar(uint16_t x,uint16_t y,uint8_t num,uint8_t size,uint8_t mode)
{
uint8_t temp,t1,t;
uint16_t y0=y;
uint8_t csize=(size/8+((size%8)?1:0))*(size/2); //得到字体一个字符对应点阵集所占的字节数
num=num-' ';//得到偏移后的值（ASCII字库是从空格开始取模，所以-' '就是对应字符的字库）
for(t=0; t<csize; t++)
{
if(size==12)temp=asc2_1206[num][t]; //调用1206字体
else if(size==16)temp=asc2_1608[num][t]; //调用1608字体
else if(size==24)temp=asc2_2412[num][t]; //调用2412字体
else if(size==32)temp=asc2_3216[num][t]; //调用3216字体
else return; //没有的字库
for(t1=0; t1<8; t1++)
{
if(temp&0x80)LCD_Fast_DrawPoint(x,y,POINT_COLOR);
else if(mode==0)LCD_Fast_DrawPoint(x,y,BACK_COLOR);
temp<<=1;
y++;
if(y>=lcddev.height)return; //超区域了
if((y-y0)==size)
{
y=y0;
x++;
if(x>=lcddev.width)return; //超区域了
break;
}
}
}
}
//m^n函数，LCD显示数字内部使用
//返回值:m^n次方.
uint32_t _LCD_Pow(uint8_t m,uint8_t n)
{
uint32_t result=1;
while(n--)result*=m;
return result;
}
//显示数字,高位为0,则不显示
//x,y :起点坐标
//len :数字的位数
//size:字体大小
//color:颜色
//num:数值(0~4294967295);
void LCD_ShowNum(uint16_t x, uint16_t y, uint32_t num, uint8_t len, uint8_t size)
{
uint8_t t, temp;
uint8_t enshow = 0;
for (t = 0; t < len; t++)
{
temp = (num / _LCD_Pow(10, len - t - 1)) % 10;
if (enshow == 0 && t < (len - 1))
{
if (temp == 0)
{
LCD_ShowChar(x + (size / 2)*t, y, ' ', size, 0);
continue;
}
else enshow = 1;
}
LCD_ShowChar(x + (size / 2)*t, y, temp + '0', size, 0);
}
}
//显示数字,高位为0,还是显示
//x,y:起点坐标
//num:数值(0~999999999);
//len:长度(即要显示的位数)
//size:字体大小
//mode:
//[7]:0,不填充;1,填充0.
//[6:1]:保留
//[0]:0,非叠加显示;1,叠加显示.
void LCD_ShowxNum(uint16_t x,uint16_t y,uint32_t num,uint8_t len,uint8_t size,uint8_t mode)
{
uint8_t t,temp;
uint8_t enshow=0;
for(t=0; t<len; t++)
{
temp=(num/_LCD_Pow(10,len-t-1))%10;
if(enshow==0&&t<(len-1))
{
if(temp==0)
{
if(mode&0X80)LCD_ShowChar(x+(size/2)*t,y,'0',size,mode&0X01);
else LCD_ShowChar(x+(size/2)*t,y,' ',size,mode&0X01);
continue;
} else enshow=1;
}
LCD_ShowChar(x+(size/2)*t,y,temp+'0',size,mode&0X01);
}
}
//显示字符串
//x,y:起点坐标
//width,height:区域大小
//size:字体大小
//*p:字符串起始地址
void LCD_ShowString(uint16_t x, uint16_t y, uint16_t width, uint16_t height, uint8_t size, uint8_t *p)
{
uint8_t x0 = x;
width += x;
height += y;
while ((*p <= '~') && (*p >= ' ')) //判断是不是非法字符!
{
if (x >= width)
{
x = x0;
y += size;
}
if (y >= height)break; //退出
LCD_ShowChar(x, y, *p, size, 0);
x += size / 2;
p++;
}
}
tftlcd.h文件
点击查看代码
#ifndef __TFTLCD_H
#define __TFTLCD_H
#include "main.h"
#include "stdlib.h"
//
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//ALIENTEK STM32开发板
//2.8寸/3.5寸/4.3寸/7寸 TFT液晶驱动
//支持驱动IC型号包括:ILI9341/NT35310/NT35510/SSD1963等
//正点原子@ALIENTEK
//技术论坛:www.openedv.com
//创建日期:2017/4/8
//版本：V4.0
//版权所有，盗版必究。
//Copyright(C) 广州市星翼电子科技有限公司 2014-2024
//All rights reserved
//*******************************************************************************
//修改说明
//V4.0 20266666611
//1，去掉大部分不常用驱动IC的支持
//2，新增对ST7789驱动IC的支持
//3，优化代码结构（精简源码）
//
//LCD重要参数集
typedef struct
{
uint16_t width; //LCD 宽度
uint16_t height; //LCD 高度
uint16_t id; //LCD ID
uint8_t dir; //横屏还是竖屏控制：0，竖屏；1，横屏。
uint16_t wramcmd; //开始写gram指令
uint16_t setxcmd; //设置x坐标指令
uint16_t setycmd; //设置y坐标指令
}_lcd_dev;
//LCD参数
extern _lcd_dev lcddev; //管理LCD重要参数
//LCD的画笔颜色和背景色
extern uint32_t POINT_COLOR; //默认红色
extern uint32_t BACK_COLOR; //背景颜色.默认为白色
//
//-----------------MCU屏 LCD端口定义----------------
//LCD地址结构体
typedef struct
{
volatile uint16_t LCD_REG;
volatile uint16_t LCD_RAM;
} LCD_TypeDef;
#define LCD_BASE ((uint32_t)(0x6C000000 | 0x0000007E))
#define LCD ((LCD_TypeDef *) LCD_BASE)
//
//LCD分辨率设置
#define SSD_HOR_RESOLUTION 800 //LCD水平分辨率
#define SSD_VER_RESOLUTION 480 //LCD垂直分辨率
//扫描方向定义
#define L2R_U2D 0 //从左到右,从上到下
#define L2R_D2U 1 //从左到右,从下到上
#define R2L_U2D 2 //从右到左,从上到下
#define R2L_D2U 3 //从右到左,从下到上
#define U2D_L2R 4 //从上到下,从左到右
#define U2D_R2L 5 //从上到下,从右到左
#define D2U_L2R 6 //从下到上,从左到右
#define D2U_R2L 7 //从下到上,从右到左
#define DFT_SCAN_DIR L2R_U2D //默认的扫描方向
//画笔颜色
#define WHITE 0xFFFF
#define BLACK 0x0000
#define BLUE 0x001F
#define BRED 0XF81F
#define GRED 0XFFE0
#define GBLUE 0X07FF
#define RED 0xF800
#define MAGENTA 0xF81F
#define GREEN 0x07E0
#define CYAN 0x7FFF
#define YELLOW 0xFFE0
#define BROWN 0XBC40 //棕色
#define BRRED 0XFC07 //棕红色
#define GRAY 0X8430 //灰色
//GUI颜色
#define DARKBLUE 0X01CF //深蓝色
#define LIGHTBLUE 0X7D7C //浅蓝色
#define GRAYBLUE 0X5458 //灰蓝色
//以上三色为PANEL的颜色
#define LIGHTGREEN 0X841F //浅绿色
#define LGRAY 0XC618 //浅灰色(PANNEL),窗体背景色
#define LGRAYBLUE 0XA651 //浅灰蓝色(中间层颜色)
#define LBBLUE 0X2B12 //浅棕蓝色(选择条目的反色)
/*应用函数*/
//初始化
void LCD_Init(void);
//开显示
void LCD_DisplayOn(void);
//关显示
void LCD_DisplayOff(void);
//清屏
void LCD_Clear(uint32_t Color);
//设置光标
void LCD_SetCursor(uint16_t Xpos, uint16_t Ypos);
//画点
void LCD_DrawPoint(uint16_t x,uint16_t y);
//快速画点
void LCD_Fast_DrawPoint(uint16_t x,uint16_t y,uint32_t color);
//读点
uint32_t LCD_ReadPoint(uint16_t x,uint16_t y);
//画圆
void LCD_Draw_Circle(uint16_t x0,uint16_t y0,uint8_t r);
//画线
void LCD_DrawLine(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2);
//画矩形
void LCD_DrawRectangle(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2);
//填充单色
void LCD_Fill(uint16_t sx,uint16_t sy,uint16_t ex,uint16_t ey,uint32_t color);
//填充指定颜色
void LCD_Color_Fill(uint16_t sx,uint16_t sy,uint16_t ex,uint16_t ey,uint16_t *color);
//显示一个字符
void LCD_ShowChar(uint16_t x,uint16_t y,uint8_t num,uint8_t size,uint8_t mode);
//显示一个数字
void LCD_ShowNum(uint16_t x,uint16_t y,uint32_t num,uint8_t len,uint8_t size);
//显示 数字
void LCD_ShowxNum(uint16_t x,uint16_t y,uint32_t num,uint8_t len,uint8_t size,uint8_t mode);
//显示一个字符串,12/16字体
void LCD_ShowString(uint16_t x,uint16_t y,uint16_t width,uint16_t height,uint8_t size,uint8_t *p);
/*底层函数*/
void LCD_WriteReg(uint16_t LCD_Reg, uint16_t LCD_RegValue);
uint16_t LCD_ReadReg(uint16_t LCD_Reg);
void LCD_WriteRAM_Prepare(void);
void LCD_WriteRAM(uint16_t RGB_Code);
//SSD1963 背光控制
void LCD_SSD_BackLightSet(uint8_t pwm);
//设置屏扫描方向
void LCD_Scan_Dir(uint8_t dir);
//设置屏幕显示方向
void LCD_Display_Dir(uint8_t dir);
//设置窗口
void LCD_Set_Window(uint16_t sx,uint16_t sy,uint16_t width,uint16_t height);
//LCD驱动参数设置
#define SSD_HOR_PULSE_WIDTH 1 //水平脉宽
#define SSD_HOR_BACK_PORCH 46 //水平前廊
#define SSD_HOR_FRONT_PORCH 210 //水平后廊
#define SSD_VER_PULSE_WIDTH 1 //垂直脉宽
#define SSD_VER_BACK_PORCH 23 //垂直前廊
#define SSD_VER_FRONT_PORCH 22 //垂直前廊
//如下几个参数，自动计算
#define SSD_HT (SSD_HOR_RESOLUTION+SSD_HOR_BACK_PORCH+SSD_HOR_FRONT_PORCH)
#define SSD_HPS (SSD_HOR_BACK_PORCH)
#define SSD_VT (SSD_VER_RESOLUTION+SSD_VER_BACK_PORCH+SSD_VER_FRONT_PORCH)
#define SSD_VPS (SSD_VER_BACK_PORCH)
#endif
font.h文件
点击查看代码
#ifndef __FONT_H
#define __FONT_H
//常用ASCII表
//偏移量32
//ASCII字符集: !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~
//PC2LCD2002取模方式设置：阴码+逐列式+顺向+C51格式
//总共：3个字符集（12*12、16*16、24*24和32*32），用户可以自行新增其他分辨率的字符集。
//每个字符所占用的字节数为:(size/8+((size%8)?1:0))*(size/2),其中size:是字库生成时的点阵大小(12/16/24/32...)
//12*12 ASCII字符集点阵
const unsigned char asc2_1206[95][12]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x3F,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x30,0x00,0x40,0x00,0x30,0x00,0x40,0x00,0x00,0x00},/*""",2*/
{0x09,0x00,0x0B,0xC0,0x3D,0x00,0x0B,0xC0,0x3D,0x00,0x09,0x00},/*"#",3*/
{0x18,0xC0,0x24,0x40,0x7F,0xE0,0x22,0x40,0x31,0x80,0x00,0x00},/*"$",4*/
{0x18,0x00,0x24,0xC0,0x1B,0x00,0x0D,0x80,0x32,0x40,0x01,0x80},/*"%",5*/
{0x03,0x80,0x1C,0x40,0x27,0x40,0x1C,0x80,0x07,0x40,0x00,0x40},/*"&",6*/
{0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x80,0x20,0x40,0x40,0x20},/*"(",8*/
{0x00,0x00,0x40,0x20,0x20,0x40,0x1F,0x80,0x00,0x00,0x00,0x00},/*")",9*/
{0x09,0x00,0x06,0x00,0x1F,0x80,0x06,0x00,0x09,0x00,0x00,0x00},/*"*",10*/
{0x04,0x00,0x04,0x00,0x3F,0x80,0x04,0x00,0x04,0x00,0x00,0x00},/*"+",11*/
{0x00,0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x20,0x01,0xC0,0x06,0x00,0x38,0x00,0x40,0x00,0x00,0x00},/*"/",15*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"0",16*/
{0x00,0x00,0x10,0x40,0x3F,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"1",17*/
{0x18,0xC0,0x21,0x40,0x22,0x40,0x24,0x40,0x18,0x40,0x00,0x00},/*"2",18*/
{0x10,0x80,0x20,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"3",19*/
{0x02,0x00,0x0D,0x00,0x11,0x00,0x3F,0xC0,0x01,0x40,0x00,0x00},/*"4",20*/
{0x3C,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x23,0x80,0x00,0x00},/*"5",21*/
{0x1F,0x80,0x24,0x40,0x24,0x40,0x34,0x40,0x03,0x80,0x00,0x00},/*"6",22*/
{0x30,0x00,0x20,0x00,0x27,0xC0,0x38,0x00,0x20,0x00,0x00,0x00},/*"7",23*/
{0x1B,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"8",24*/
{0x1C,0x00,0x22,0xC0,0x22,0x40,0x22,0x40,0x1F,0x80,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x08,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x04,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x04,0x00,0x0A,0x00,0x11,0x00,0x20,0x80,0x40,0x40},/*"<",28*/
{0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x40,0x40,0x20,0x80,0x11,0x00,0x0A,0x00,0x04,0x00},/*">",30*/
{0x18,0x00,0x20,0x00,0x23,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"?",31*/
{0x1F,0x80,0x20,0x40,0x27,0x40,0x29,0x40,0x1F,0x40,0x00,0x00},/*"@",32*/
{0x00,0x40,0x07,0xC0,0x39,0x00,0x0F,0x00,0x01,0xC0,0x00,0x40},/*"A",33*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"B",34*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x30,0x80,0x00,0x00},/*"C",35*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"D",36*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x40,0x30,0xC0,0x00,0x00},/*"E",37*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x00,0x30,0x00,0x00,0x00},/*"F",38*/
{0x0F,0x00,0x10,0x80,0x20,0x40,0x22,0x40,0x33,0x80,0x02,0x00},/*"G",39*/
{0x20,0x40,0x3F,0xC0,0x04,0x00,0x04,0x00,0x3F,0xC0,0x20,0x40},/*"H",40*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x00,0x00},/*"I",41*/
{0x00,0x60,0x20,0x20,0x20,0x20,0x3F,0xC0,0x20,0x00,0x20,0x00},/*"J",42*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x0B,0x00,0x30,0xC0,0x20,0x40},/*"K",43*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x00,0x40,0x00,0x40,0x00,0xC0},/*"L",44*/
{0x3F,0xC0,0x3C,0x00,0x03,0xC0,0x3C,0x00,0x3F,0xC0,0x00,0x00},/*"M",45*/
{0x20,0x40,0x3F,0xC0,0x0C,0x40,0x23,0x00,0x3F,0xC0,0x20,0x00},/*"N",46*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"O",47*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"P",48*/
{0x1F,0x80,0x21,0x40,0x21,0x40,0x20,0xE0,0x1F,0xA0,0x00,0x00},/*"Q",49*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x26,0x00,0x19,0xC0,0x00,0x40},/*"R",50*/
{0x18,0xC0,0x24,0x40,0x24,0x40,0x22,0x40,0x31,0x80,0x00,0x00},/*"S",51*/
{0x30,0x00,0x20,0x40,0x3F,0xC0,0x20,0x40,0x30,0x00,0x00,0x00},/*"T",52*/
{0x20,0x00,0x3F,0x80,0x00,0x40,0x00,0x40,0x3F,0x80,0x20,0x00},/*"U",53*/
{0x20,0x00,0x3E,0x00,0x01,0xC0,0x07,0x00,0x38,0x00,0x20,0x00},/*"V",54*/
{0x38,0x00,0x07,0xC0,0x3C,0x00,0x07,0xC0,0x38,0x00,0x00,0x00},/*"W",55*/
{0x20,0x40,0x39,0xC0,0x06,0x00,0x39,0xC0,0x20,0x40,0x00,0x00},/*"X",56*/
{0x20,0x00,0x38,0x40,0x07,0xC0,0x38,0x40,0x20,0x00,0x00,0x00},/*"Y",57*/
{0x30,0x40,0x21,0xC0,0x26,0x40,0x38,0x40,0x20,0xC0,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x7F,0xE0,0x40,0x20,0x40,0x20,0x00,0x00},/*"[",59*/
{0x00,0x00,0x70,0x00,0x0C,0x00,0x03,0x80,0x00,0x40,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x20,0x40,0x20,0x7F,0xE0,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x20,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10},/*"_",63*/
{0x00,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x02,0x80,0x05,0x40,0x05,0x40,0x03,0xC0,0x00,0x40},/*"a",65*/
{0x20,0x00,0x3F,0xC0,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"b",66*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x06,0x40,0x00,0x00},/*"c",67*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x24,0x40,0x3F,0xC0,0x00,0x40},/*"d",68*/
{0x00,0x00,0x03,0x80,0x05,0x40,0x05,0x40,0x03,0x40,0x00,0x00},/*"e",69*/
{0x00,0x00,0x04,0x40,0x1F,0xC0,0x24,0x40,0x24,0x40,0x20,0x00},/*"f",70*/
{0x00,0x00,0x02,0xE0,0x05,0x50,0x05,0x50,0x06,0x50,0x04,0x20},/*"g",71*/
{0x20,0x40,0x3F,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"h",72*/
{0x00,0x00,0x04,0x40,0x27,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x10,0x00,0x10,0x04,0x10,0x27,0xE0,0x00,0x00,0x00,0x00},/*"j",74*/
{0x20,0x40,0x3F,0xC0,0x01,0x40,0x07,0x00,0x04,0xC0,0x04,0x40},/*"k",75*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x00,0x40,0x00,0x40,0x00,0x00},/*"l",76*/
{0x07,0xC0,0x04,0x00,0x07,0xC0,0x04,0x00,0x03,0xC0,0x00,0x00},/*"m",77*/
{0x04,0x40,0x07,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"n",78*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"o",79*/
{0x04,0x10,0x07,0xF0,0x04,0x50,0x04,0x40,0x03,0x80,0x00,0x00},/*"p",80*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x50,0x07,0xF0,0x00,0x10},/*"q",81*/
{0x04,0x40,0x07,0xC0,0x02,0x40,0x04,0x00,0x04,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x06,0x40,0x05,0x40,0x05,0x40,0x04,0xC0,0x00,0x00},/*"s",83*/
{0x00,0x00,0x04,0x00,0x1F,0x80,0x04,0x40,0x00,0x40,0x00,0x00},/*"t",84*/
{0x04,0x00,0x07,0x80,0x00,0x40,0x04,0x40,0x07,0xC0,0x00,0x40},/*"u",85*/
{0x04,0x00,0x07,0x00,0x04,0xC0,0x01,0x80,0x06,0x00,0x04,0x00},/*"v",86*/
{0x06,0x00,0x01,0xC0,0x07,0x00,0x01,0xC0,0x06,0x00,0x00,0x00},/*"w",87*/
{0x04,0x40,0x06,0xC0,0x01,0x00,0x06,0xC0,0x04,0x40,0x00,0x00},/*"x",88*/
{0x04,0x10,0x07,0x10,0x04,0xE0,0x01,0x80,0x06,0x00,0x04,0x00},/*"y",89*/
{0x00,0x00,0x04,0x40,0x05,0xC0,0x06,0x40,0x04,0x40,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x04,0x00,0x7B,0xE0,0x40,0x20,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xF0,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x20,0x7B,0xE0,0x04,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x40,0x00,0x80,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x40,0x00},/*"~",94*/
};
//16*16 ASCII字符集点阵
const unsigned char asc2_1608[95][16]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xCC,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x00,0x00},/*""",2*/
{0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x00,0x00},/*"#",3*/
{0x00,0x00,0x0E,0x18,0x11,0x04,0x3F,0xFF,0x10,0x84,0x0C,0x78,0x00,0x00,0x00,0x00},/*"$",4*/
{0x0F,0x00,0x10,0x84,0x0F,0x38,0x00,0xC0,0x07,0x78,0x18,0x84,0x00,0x78,0x00,0x00},/*"%",5*/
{0x00,0x78,0x0F,0x84,0x10,0xC4,0x11,0x24,0x0E,0x98,0x00,0xE4,0x00,0x84,0x00,0x08},/*"&",6*/
{0x08,0x00,0x68,0x00,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xE0,0x18,0x18,0x20,0x04,0x40,0x02,0x00,0x00},/*"(",8*/
{0x00,0x00,0x40,0x02,0x20,0x04,0x18,0x18,0x07,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x02,0x40,0x02,0x40,0x01,0x80,0x0F,0xF0,0x01,0x80,0x02,0x40,0x02,0x40,0x00,0x00},/*"*",10*/
{0x00,0x80,0x00,0x80,0x00,0x80,0x0F,0xF8,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x00},/*"+",11*/
{0x00,0x01,0x00,0x0D,0x00,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80},/*"-",13*/
{0x00,0x00,0x00,0x0C,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x06,0x00,0x18,0x00,0x60,0x01,0x80,0x06,0x00,0x18,0x00,0x20,0x00},/*"/",15*/
{0x00,0x00,0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"0",16*/
{0x00,0x00,0x08,0x04,0x08,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x0E,0x0C,0x10,0x14,0x10,0x24,0x10,0x44,0x11,0x84,0x0E,0x0C,0x00,0x00},/*"2",18*/
{0x00,0x00,0x0C,0x18,0x10,0x04,0x11,0x04,0x11,0x04,0x12,0x88,0x0C,0x70,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0xE0,0x03,0x20,0x04,0x24,0x08,0x24,0x1F,0xFC,0x00,0x24,0x00,0x00},/*"4",20*/
{0x00,0x00,0x1F,0x98,0x10,0x84,0x11,0x04,0x11,0x04,0x10,0x88,0x10,0x70,0x00,0x00},/*"5",21*/
{0x00,0x00,0x07,0xF0,0x08,0x88,0x11,0x04,0x11,0x04,0x18,0x88,0x00,0x70,0x00,0x00},/*"6",22*/
{0x00,0x00,0x1C,0x00,0x10,0x00,0x10,0xFC,0x13,0x00,0x1C,0x00,0x10,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x0E,0x38,0x11,0x44,0x10,0x84,0x10,0x84,0x11,0x44,0x0E,0x38,0x00,0x00},/*"8",24*/
{0x00,0x00,0x07,0x00,0x08,0x8C,0x10,0x44,0x10,0x44,0x08,0x88,0x07,0xF0,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0C,0x03,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x80,0x01,0x40,0x02,0x20,0x04,0x10,0x08,0x08,0x10,0x04,0x00,0x00},/*"<",28*/
{0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x00,0x00},/*"=",29*/
{0x00,0x00,0x10,0x04,0x08,0x08,0x04,0x10,0x02,0x20,0x01,0x40,0x00,0x80,0x00,0x00},/*">",30*/
{0x00,0x00,0x0E,0x00,0x12,0x00,0x10,0x0C,0x10,0x6C,0x10,0x80,0x0F,0x00,0x00,0x00},/*"?",31*/
{0x03,0xE0,0x0C,0x18,0x13,0xE4,0x14,0x24,0x17,0xC4,0x08,0x28,0x07,0xD0,0x00,0x00},/*"@",32*/
{0x00,0x04,0x00,0x3C,0x03,0xC4,0x1C,0x40,0x07,0x40,0x00,0xE4,0x00,0x1C,0x00,0x04},/*"A",33*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x11,0x04,0x0E,0x88,0x00,0x70,0x00,0x00},/*"B",34*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x04,0x10,0x08,0x1C,0x10,0x00,0x00},/*"C",35*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"D",36*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x17,0xC4,0x10,0x04,0x08,0x18,0x00,0x00},/*"E",37*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x17,0xC0,0x10,0x00,0x08,0x00,0x00,0x00},/*"F",38*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x44,0x1C,0x78,0x00,0x40,0x00,0x00},/*"G",39*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x00,0x80,0x00,0x80,0x10,0x84,0x1F,0xFC,0x10,0x04},/*"H",40*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x03,0x00,0x01,0x10,0x01,0x10,0x01,0x1F,0xFE,0x10,0x00,0x10,0x00,0x00,0x00},/*"J",42*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x03,0x80,0x14,0x64,0x18,0x1C,0x10,0x04,0x00,0x00},/*"K",43*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x0C,0x00,0x00},/*"L",44*/
{0x10,0x04,0x1F,0xFC,0x1F,0x00,0x00,0xFC,0x1F,0x00,0x1F,0xFC,0x10,0x04,0x00,0x00},/*"M",45*/
{0x10,0x04,0x1F,0xFC,0x0C,0x04,0x03,0x00,0x00,0xE0,0x10,0x18,0x1F,0xFC,0x10,0x00},/*"N",46*/
{0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"O",47*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x10,0x80,0x10,0x80,0x10,0x80,0x0F,0x00,0x00,0x00},/*"P",48*/
{0x07,0xF0,0x08,0x18,0x10,0x24,0x10,0x24,0x10,0x1C,0x08,0x0A,0x07,0xF2,0x00,0x00},/*"Q",49*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x11,0xC0,0x11,0x30,0x0E,0x0C,0x00,0x04},/*"R",50*/
{0x00,0x00,0x0E,0x1C,0x11,0x04,0x10,0x84,0x10,0x84,0x10,0x44,0x1C,0x38,0x00,0x00},/*"S",51*/
{0x18,0x00,0x10,0x00,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x00,0x18,0x00,0x00,0x00},/*"T",52*/
{0x10,0x00,0x1F,0xF8,0x10,0x04,0x00,0x04,0x00,0x04,0x10,0x04,0x1F,0xF8,0x10,0x00},/*"U",53*/
{0x10,0x00,0x1E,0x00,0x11,0xE0,0x00,0x1C,0x00,0x70,0x13,0x80,0x1C,0x00,0x10,0x00},/*"V",54*/
{0x1F,0xC0,0x10,0x3C,0x00,0xE0,0x1F,0x00,0x00,0xE0,0x10,0x3C,0x1F,0xC0,0x00,0x00},/*"W",55*/
{0x10,0x04,0x18,0x0C,0x16,0x34,0x01,0xC0,0x01,0xC0,0x16,0x34,0x18,0x0C,0x10,0x04},/*"X",56*/
{0x10,0x00,0x1C,0x00,0x13,0x04,0x00,0xFC,0x13,0x04,0x1C,0x00,0x10,0x00,0x00,0x00},/*"Y",57*/
{0x08,0x04,0x10,0x1C,0x10,0x64,0x10,0x84,0x13,0x04,0x1C,0x04,0x10,0x18,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFE,0x40,0x02,0x40,0x02,0x40,0x02,0x00,0x00},/*"[",59*/
{0x00,0x00,0x30,0x00,0x0C,0x00,0x03,0x80,0x00,0x60,0x00,0x1C,0x00,0x03,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x40,0x02,0x7F,0xFE,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00},/*"^",62*/
{0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01},/*"_",63*/
{0x00,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x98,0x01,0x24,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xFC,0x00,0x04},/*"a",65*/
{0x10,0x00,0x1F,0xFC,0x00,0x88,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x11,0x08,0x1F,0xFC,0x00,0x04},/*"d",68*/
{0x00,0x00,0x00,0xF8,0x01,0x44,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xC8,0x00,0x00},/*"e",69*/
{0x00,0x00,0x01,0x04,0x01,0x04,0x0F,0xFC,0x11,0x04,0x11,0x04,0x11,0x00,0x18,0x00},/*"f",70*/
{0x00,0x00,0x00,0xD6,0x01,0x29,0x01,0x29,0x01,0x29,0x01,0xC9,0x01,0x06,0x00,0x00},/*"g",71*/
{0x10,0x04,0x1F,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"h",72*/
{0x00,0x00,0x01,0x04,0x19,0x04,0x19,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x03,0x00,0x01,0x01,0x01,0x19,0x01,0x19,0xFE,0x00,0x00,0x00,0x00},/*"j",74*/
{0x10,0x04,0x1F,0xFC,0x00,0x24,0x00,0x40,0x01,0xB4,0x01,0x0C,0x01,0x04,0x00,0x00},/*"k",75*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"l",76*/
{0x01,0x04,0x01,0xFC,0x01,0x04,0x01,0x00,0x01,0xFC,0x01,0x04,0x01,0x00,0x00,0xFC},/*"m",77*/
{0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"n",78*/
{0x00,0x00,0x00,0xF8,0x01,0x04,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0xF8,0x00,0x00},/*"o",79*/
{0x01,0x01,0x01,0xFF,0x00,0x85,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x05,0x01,0xFF,0x00,0x01},/*"q",81*/
{0x01,0x04,0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x04,0x01,0x00,0x01,0x80,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0xCC,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x98,0x00,0x00},/*"s",83*/
{0x00,0x00,0x01,0x00,0x01,0x00,0x07,0xF8,0x01,0x04,0x01,0x04,0x00,0x00,0x00,0x00},/*"t",84*/
{0x01,0x00,0x01,0xF8,0x00,0x04,0x00,0x04,0x00,0x04,0x01,0x08,0x01,0xFC,0x00,0x04},/*"u",85*/
{0x01,0x00,0x01,0x80,0x01,0x70,0x00,0x0C,0x00,0x10,0x01,0x60,0x01,0x80,0x01,0x00},/*"v",86*/
{0x01,0xF0,0x01,0x0C,0x00,0x30,0x01,0xC0,0x00,0x30,0x01,0x0C,0x01,0xF0,0x01,0x00},/*"w",87*/
{0x00,0x00,0x01,0x04,0x01,0x8C,0x00,0x74,0x01,0x70,0x01,0x8C,0x01,0x04,0x00,0x00},/*"x",88*/
{0x01,0x01,0x01,0x81,0x01,0x71,0x00,0x0E,0x00,0x18,0x01,0x60,0x01,0x80,0x01,0x00},/*"y",89*/
{0x00,0x00,0x01,0x84,0x01,0x0C,0x01,0x34,0x01,0x44,0x01,0x84,0x01,0x0C,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x3E,0xFC,0x40,0x02,0x40,0x02},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x3E,0xFC,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x60,0x00,0x80,0x00,0x80,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x20,0x00},/*"~",94*/
};
//24*24 ASICII字符集点阵
const unsigned char asc2_2412[95][36]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x80,0x38,0x0F,0xFE,0x38,0x0F,0x80,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x06,0x00,0x00,0x0C,0x00,0x00,0x38,0x00,0x00,0x31,0x00,0x00,0x06,0x00,0x00,0x0C,0x00,0x00,0x38,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x00,0x61,0x80,0x00,0x67,0xF8,0x07,0xF9,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x67,0xF8,0x07,0xF9,0x80,0x00,0x61,0x80,0x00,0x00,0x00},/*"#",3*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0xE0,0x03,0xE0,0xF0,0x06,0x30,0x08,0x04,0x18,0x08,0x1F,0xFF,0xFE,0x04,0x0E,0x08,0x07,0x87,0xF0,0x03,0x81,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"$",4*/
{0x01,0xF0,0x00,0x06,0x0C,0x00,0x04,0x04,0x08,0x06,0x0C,0x70,0x01,0xF9,0xC0,0x00,0x0E,0x00,0x00,0x3B,0xE0,0x00,0xEC,0x18,0x07,0x08,0x08,0x04,0x0C,0x18,0x00,0x03,0xE0,0x00,0x00,0x00},/*"%",5*/
{0x00,0x01,0xE0,0x00,0x07,0xF0,0x03,0xF8,0x18,0x04,0x1C,0x08,0x04,0x17,0x08,0x07,0xE1,0xD0,0x03,0xC0,0xE0,0x00,0x23,0xB0,0x00,0x3C,0x08,0x00,0x20,0x08,0x00,0x00,0x10,0x00,0x00,0x00},/*"&",6*/
{0x00,0x00,0x00,0x01,0x00,0x00,0x31,0x00,0x00,0x32,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x01,0xFF,0xC0,0x07,0x80,0xF0,0x0C,0x00,0x18,0x10,0x00,0x04,0x20,0x00,0x02,0x00,0x00,0x00},/*"(",8*/
{0x00,0x00,0x00,0x20,0x00,0x02,0x10,0x00,0x04,0x0C,0x00,0x18,0x07,0x80,0xF0,0x01,0xFF,0xC0,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x42,0x00,0x00,0x66,0x00,0x00,0x66,0x00,0x00,0x3C,0x00,0x00,0x18,0x00,0x03,0xFF,0xC0,0x00,0x18,0x00,0x00,0x3C,0x00,0x00,0x66,0x00,0x00,0x66,0x00,0x00,0x42,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x01,0xFF,0xC0,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x31,0x00,0x00,0x32,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x00,0x00,0x38,0x00,0x00,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x1C,0x00,0x00,0x70,0x00,0x01,0x80,0x00,0x0E,0x00,0x00,0x38,0x00,0x00,0xC0,0x00,0x07,0x00,0x00,0x1C,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00},/*"/",15*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x03,0x80,0x70,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x08,0x01,0x00,0x08,0x01,0x00,0x08,0x03,0xFF,0xF8,0x07,0xFF,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x01,0xC0,0x38,0x02,0xC0,0x58,0x04,0x00,0x98,0x04,0x01,0x18,0x04,0x02,0x18,0x04,0x04,0x18,0x06,0x1C,0x18,0x03,0xF8,0x18,0x01,0xE0,0xF8,0x00,0x00,0x00,0x00,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x01,0xC0,0xE0,0x03,0xC0,0xF0,0x04,0x00,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x06,0x18,0x08,0x03,0xF4,0x18,0x01,0xE7,0xF0,0x00,0x01,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x0D,0x00,0x00,0x11,0x00,0x00,0x61,0x00,0x00,0x81,0x08,0x03,0x01,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x01,0x08,0x00,0x01,0x08,0x00,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x00,0x00,0xE0,0x07,0xFC,0xD0,0x06,0x08,0x08,0x06,0x10,0x08,0x06,0x10,0x08,0x06,0x10,0x08,0x06,0x18,0x38,0x06,0x0F,0xF0,0x06,0x07,0xC0,0x00,0x00,0x00,0x00,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x84,0x30,0x02,0x08,0x18,0x04,0x10,0x08,0x04,0x10,0x08,0x04,0x10,0x08,0x07,0x18,0x10,0x03,0x0F,0xF0,0x00,0x07,0xC0,0x00,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xC0,0x00,0x07,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0xF8,0x06,0x07,0xF8,0x06,0x18,0x00,0x06,0xE0,0x00,0x07,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x01,0xE1,0xE0,0x03,0xF7,0xF0,0x06,0x34,0x10,0x04,0x18,0x08,0x04,0x18,0x08,0x04,0x0C,0x08,0x04,0x0C,0x08,0x06,0x16,0x18,0x03,0xF3,0xF0,0x01,0xC1,0xE0,0x00,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x00,0xF8,0x00,0x03,0xFC,0x30,0x03,0x06,0x38,0x04,0x02,0x08,0x04,0x02,0x08,0x04,0x02,0x08,0x04,0x04,0x10,0x03,0x08,0xF0,0x01,0xFF,0xC0,0x00,0x7F,0x00,0x00,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x38,0x00,0x70,0x38,0x00,0x70,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x1A,0x00,0x30,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x14,0x00,0x00,0x22,0x00,0x00,0x41,0x00,0x00,0x80,0x80,0x01,0x00,0x40,0x02,0x00,0x20,0x04,0x00,0x10,0x08,0x00,0x08,0x00,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x08,0x04,0x00,0x10,0x02,0x00,0x20,0x01,0x00,0x40,0x00,0x80,0x80,0x00,0x41,0x00,0x00,0x22,0x00,0x00,0x14,0x00,0x00,0x08,0x00,0x00,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x03,0xC0,0x00,0x04,0xC0,0x00,0x04,0x00,0x00,0x08,0x00,0x38,0x08,0x0F,0x38,0x08,0x08,0x38,0x08,0x10,0x00,0x0C,0x30,0x00,0x07,0xE0,0x00,0x03,0xC0,0x00,0x00,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x00,0xFF,0xE0,0x03,0x80,0x70,0x02,0x0F,0x10,0x06,0x70,0x88,0x04,0xC0,0x88,0x04,0x83,0x08,0x04,0x7F,0x88,0x02,0xC0,0x90,0x03,0x01,0x20,0x00,0xFE,0x40},/*"@",32*/
{0x00,0x00,0x08,0x00,0x00,0x18,0x00,0x01,0xF8,0x00,0x3E,0x08,0x01,0xC2,0x00,0x07,0x02,0x00,0x07,0xE2,0x00,0x00,0xFE,0x00,0x00,0x1F,0xC8,0x00,0x01,0xF8,0x00,0x00,0x38,0x00,0x00,0x08},/*"A",33*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x06,0x18,0x08,0x03,0xF4,0x18,0x01,0xE7,0xF0,0x00,0x01,0xE0,0x00,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x02,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x10,0x06,0x00,0x20,0x07,0x80,0xC0,0x00,0x00,0x00},/*"C",35*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x18,0x02,0x00,0x10,0x03,0x80,0x70,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"D",36*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x3E,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x01,0x00,0x60,0x00,0x00,0x00},/*"E",37*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x00,0x04,0x08,0x00,0x04,0x08,0x00,0x04,0x3E,0x00,0x06,0x00,0x00,0x06,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x02,0x08,0x04,0x02,0x08,0x02,0x03,0xF0,0x07,0x83,0xF0,0x00,0x02,0x00,0x00,0x02,0x00},/*"G",39*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x04,0x08,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08},/*"H",40*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x07,0x00,0x00,0x01,0x04,0x00,0x01,0x04,0x00,0x01,0x04,0x00,0x03,0x07,0xFF,0xFE,0x07,0xFF,0xFC,0x04,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00},/*"J",42*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x0C,0x08,0x00,0x18,0x00,0x00,0x3E,0x00,0x04,0xC7,0x80,0x05,0x03,0xC8,0x06,0x00,0xF8,0x04,0x00,0x38,0x04,0x00,0x18,0x00,0x00,0x08},/*"K",43*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x18,0x00,0x00,0x60,0x00,0x00,0x00},/*"L",44*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0x80,0x08,0x07,0xFC,0x00,0x00,0x7F,0xC0,0x00,0x03,0xF8,0x00,0x07,0xC0,0x00,0x78,0x00,0x07,0x80,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08},/*"M",45*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0x00,0x08,0x03,0xC0,0x00,0x00,0xE0,0x00,0x00,0x38,0x00,0x00,0x1E,0x00,0x00,0x07,0x00,0x00,0x01,0xC0,0x04,0x00,0xF0,0x07,0xFF,0xF8,0x04,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x03,0x00,0x30,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"O",47*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x04,0x08,0x04,0x04,0x00,0x04,0x04,0x00,0x04,0x04,0x00,0x04,0x04,0x00,0x06,0x0C,0x00,0x03,0xF8,0x00,0x01,0xF0,0x00,0x00,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x88,0x04,0x00,0x88,0x04,0x00,0xC8,0x06,0x00,0x3C,0x03,0x00,0x3E,0x01,0xFF,0xE6,0x00,0x7F,0x84,0x00,0x00,0x00},/*"Q",49*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x00,0x04,0x0C,0x00,0x04,0x0F,0x00,0x04,0x0B,0xC0,0x06,0x10,0xF0,0x03,0xF0,0x38,0x01,0xE0,0x08,0x00,0x00,0x08},/*"R",50*/
{0x00,0x00,0x00,0x01,0xE0,0xF8,0x03,0xF0,0x30,0x06,0x30,0x10,0x04,0x18,0x08,0x04,0x18,0x08,0x04,0x0C,0x08,0x04,0x0C,0x08,0x02,0x06,0x18,0x02,0x07,0xF0,0x07,0x81,0xE0,0x00,0x00,0x00},/*"S",51*/
{0x01,0x80,0x00,0x06,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x00,0x04,0x00,0x00,0x06,0x00,0x00,0x01,0x80,0x00},/*"T",52*/
{0x04,0x00,0x00,0x07,0xFF,0xE0,0x07,0xFF,0xF0,0x04,0x00,0x18,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x04,0x00,0x10,0x07,0xFF,0xE0,0x04,0x00,0x00},/*"U",53*/
{0x04,0x00,0x00,0x06,0x00,0x00,0x07,0xE0,0x00,0x07,0xFE,0x00,0x04,0x1F,0xE0,0x00,0x01,0xF8,0x00,0x00,0x38,0x00,0x01,0xE0,0x04,0x3E,0x00,0x07,0xC0,0x00,0x06,0x00,0x00,0x04,0x00,0x00},/*"V",54*/
{0x04,0x00,0x00,0x07,0xE0,0x00,0x07,0xFF,0xC0,0x04,0x1F,0xF8,0x00,0x07,0xC0,0x07,0xF8,0x00,0x07,0xFF,0x80,0x04,0x3F,0xF8,0x00,0x07,0xC0,0x04,0xF8,0x00,0x07,0x00,0x00,0x04,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x06,0x00,0x18,0x07,0xC0,0x78,0x05,0xF1,0xC8,0x00,0x3E,0x00,0x00,0x1F,0x80,0x04,0x63,0xE8,0x07,0x80,0xF8,0x06,0x00,0x18,0x04,0x00,0x08,0x00,0x00,0x00},/*"X",56*/
{0x04,0x00,0x00,0x06,0x00,0x00,0x07,0x80,0x00,0x07,0xE0,0x08,0x04,0x7C,0x08,0x00,0x1F,0xF8,0x00,0x07,0xF8,0x00,0x18,0x08,0x04,0xE0,0x08,0x07,0x00,0x00,0x06,0x00,0x00,0x04,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x01,0x00,0x08,0x06,0x00,0x38,0x04,0x00,0xF8,0x04,0x03,0xE8,0x04,0x0F,0x08,0x04,0x7C,0x08,0x05,0xF0,0x08,0x07,0xC0,0x08,0x07,0x00,0x18,0x04,0x00,0x60,0x00,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xFF,0xFE,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x00,0x00,0x00},/*"[",59*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x07,0x00,0x00,0x00,0xC0,0x00,0x00,0x38,0x00,0x00,0x06,0x00,0x00,0x01,0xC0,0x00,0x00,0x30,0x00,0x00,0x0E,0x00,0x00,0x01,0x00,0x00,0x00},/*"\",60*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x3F,0xFF,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x10,0x00,0x00,0x30,0x00,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01},/*"_",63*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x10,0x00,0x00,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x19,0xF8,0x00,0x1B,0x18,0x00,0x22,0x08,0x00,0x26,0x08,0x00,0x24,0x08,0x00,0x24,0x10,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x18},/*"a",65*/
{0x00,0x00,0x00,0x04,0x00,0x00,0x07,0xFF,0xF8,0x0F,0xFF,0xF0,0x00,0x18,0x18,0x00,0x10,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x18,0x00,0x1F,0xF0,0x00,0x0F,0xC0,0x00,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x18,0x30,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x3C,0x08,0x00,0x1C,0x10,0x00,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x38,0x18,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x04,0x10,0x10,0x07,0xFF,0xF8,0x0F,0xFF,0xF0,0x00,0x00,0x10,0x00,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x12,0x30,0x00,0x22,0x18,0x00,0x22,0x08,0x00,0x22,0x08,0x00,0x32,0x08,0x00,0x1E,0x10,0x00,0x0E,0x20,0x00,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x01,0xFF,0xF8,0x03,0xFF,0xF8,0x06,0x20,0x08,0x04,0x20,0x08,0x04,0x20,0x08,0x07,0x20,0x00,0x03,0x00,0x00,0x00,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x0E,0x00,0x0E,0x6E,0x00,0x1F,0xF3,0x00,0x31,0xB1,0x00,0x20,0xB1,0x00,0x20,0xB1,0x00,0x31,0x91,0x00,0x1F,0x13,0x00,0x2E,0x1E,0x00,0x20,0x0E,0x00,0x30,0x00},/*"g",71*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x00},/*"h",72*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x06,0x3F,0xF8,0x06,0x3F,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x03,0x00,0x20,0x01,0x00,0x20,0x01,0x00,0x20,0x03,0x06,0x3F,0xFE,0x06,0x3F,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"j",74*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x01,0x88,0x00,0x03,0x00,0x00,0x2F,0xC0,0x00,0x38,0xF8,0x00,0x20,0x38,0x00,0x20,0x08,0x00,0x00,0x08,0x00,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"l",76*/
{0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x00,0x08},/*"m",77*/
{0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x10,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x0F,0xF0,0x00,0x18,0x30,0x00,0x30,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x08,0x00,0x18,0x30,0x00,0x0F,0xF0,0x00,0x07,0xC0,0x00,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x20,0x01,0x00,0x3F,0xFF,0x00,0x3F,0xFF,0x00,0x10,0x11,0x00,0x20,0x09,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x38,0x00,0x1F,0xF0,0x00,0x0F,0xC0,0x00,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x38,0x18,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x09,0x00,0x10,0x11,0x00,0x1F,0xFF,0x00,0x3F,0xFF,0x00,0x00,0x01,0x00,0x00,0x00},/*"q",81*/
{0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x08,0x08,0x00,0x10,0x08,0x00,0x20,0x08,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x30,0x00,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x78,0x00,0x1E,0x18,0x00,0x33,0x08,0x00,0x23,0x08,0x00,0x21,0x08,0x00,0x21,0x88,0x00,0x21,0x98,0x00,0x30,0xF0,0x00,0x38,0x60,0x00,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0xFF,0xF0,0x03,0xFF,0xF8,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x3F,0xF0,0x00,0x7F,0xF8,0x00,0x00,0x18,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x20,0x10,0x00,0x3F,0xF8,0x00,0x7F,0xF0,0x00,0x00,0x10,0x00,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x3C,0x00,0x00,0x3F,0x80,0x00,0x23,0xF0,0x00,0x00,0x78,0x00,0x00,0x70,0x00,0x23,0x80,0x00,0x3C,0x00,0x00,0x30,0x00,0x00,0x20,0x00},/*"v",86*/
{0x00,0x20,0x00,0x00,0x3C,0x00,0x00,0x3F,0xE0,0x00,0x23,0xF8,0x00,0x00,0xE0,0x00,0x27,0x00,0x00,0x3E,0x00,0x00,0x3F,0xE0,0x00,0x21,0xF8,0x00,0x01,0xE0,0x00,0x3E,0x00,0x00,0x20,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x38,0x38,0x00,0x3E,0x68,0x00,0x27,0x80,0x00,0x03,0xC8,0x00,0x2C,0xF8,0x00,0x38,0x38,0x00,0x20,0x18,0x00,0x20,0x08,0x00,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x30,0x03,0x00,0x3C,0x01,0x00,0x3F,0x83,0x00,0x23,0xEC,0x00,0x00,0x70,0x00,0x23,0x80,0x00,0x3C,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x08,0x00,0x20,0x38,0x00,0x20,0xF8,0x00,0x23,0xE8,0x00,0x2F,0x88,0x00,0x3E,0x08,0x00,0x38,0x08,0x00,0x20,0x18,0x00,0x00,0x70,0x00,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x14,0x00,0x1F,0xF7,0xFC,0x30,0x00,0x06,0x20,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x02,0x30,0x00,0x06,0x1F,0xF7,0xFC,0x00,0x14,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x00,0x18,0x00,0x00,0x60,0x00,0x00,0x40,0x00,0x00,0x40,0x00,0x00,0x20,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x0C,0x00,0x00,0x10,0x00,0x00},/*"~",94*/
};
//32*32 ASCII字符集点阵
const unsigned char asc2_3216[95][128]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xF0,0x00,0xC0,0x07,0xFF,0xE1,0xE0,0x07,0xF0,0x01,0xE0,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x01,0xC0,0x00,0x00,0x07,0x80,0x00,0x00,0x1F,0x00,0x00,0x00,0x1E,0x00,0x00,0x00,0x1C,0x20,0x00,0x00,0x01,0xC0,0x00,0x00,0x07,0x80,0x00,0x00,0x1F,0x00,0x00,0x00,0x1E,0x00,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0F,0xE0,0x00,0x1F,0xFC,0x00,0x03,0xF8,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0F,0xE0,0x00,0x1F,0xFC,0x00,0x03,0xF8,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x00,0x00,0x00},/*"#",3*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x80,0x00,0x78,0x07,0xC0,0x00,0xFC,0x06,0x40,0x01,0x0E,0x00,0x20,0x03,0x07,0x00,0x20,0x02,0x03,0x80,0x20,0x0F,0xFF,0xFF,0xFC,0x02,0x01,0xC0,0x20,0x02,0x00,0xE0,0x60,0x01,0x30,0x70,0x40,0x01,0xF0,0x3F,0x80,0x00,0xF0,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"$",4*/
{0x00,0xFE,0x00,0x00,0x01,0xFF,0x00,0x00,0x03,0x01,0x80,0x00,0x02,0x00,0x80,0x60,0x03,0x01,0x81,0xC0,0x01,0xFF,0x07,0x00,0x00,0xFE,0x18,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0xBF,0x00,0x00,0x0C,0xFF,0xC0,0x00,0x71,0x80,0x60,0x01,0xC1,0x00,0x20,0x03,0x01,0x80,0x60,0x00,0x00,0xFF,0xC0,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,0x00},/*"%",5*/
{0x00,0x00,0x1F,0x00,0x00,0x00,0x7F,0xC0,0x00,0xFC,0xC0,0xC0,0x01,0xFF,0x80,0x60,0x03,0x03,0xE0,0x20,0x02,0x02,0x78,0x20,0x02,0x06,0x1E,0x20,0x03,0xFC,0x07,0x40,0x01,0xF0,0x03,0x80,0x00,0x01,0x03,0xC0,0x00,0x01,0x1C,0x60,0x00,0x01,0xE0,0x20,0x00,0x01,0x00,0x20,0x00,0x01,0x00,0x40,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00},/*"&",6*/
{0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x1C,0x60,0x00,0x00,0x1C,0x40,0x00,0x00,0x1F,0x80,0x00,0x00,0x0F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xF8,0x00,0x00,0x3F,0xFF,0x00,0x00,0x78,0x07,0xC0,0x01,0xC0,0x00,0xE0,0x03,0x00,0x00,0x30,0x04,0x00,0x00,0x08,0x08,0x00,0x00,0x04,0x10,0x00,0x00,0x02,0x00,0x00,0x00,0x00},/*"(",8*/
{0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x02,0x08,0x00,0x00,0x04,0x04,0x00,0x00,0x08,0x03,0x00,0x00,0x30,0x01,0xC0,0x00,0xE0,0x00,0x78,0x07,0xC0,0x00,0x3F,0xFF,0x00,0x00,0x07,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x18,0x00,0x00,0x0E,0x38,0x00,0x00,0x0E,0x38,0x00,0x00,0x06,0x30,0x00,0x00,0x03,0x60,0x00,0x00,0x61,0x43,0x80,0x00,0xFF,0xFF,0x80,0x00,0x61,0x43,0x00,0x00,0x03,0x60,0x00,0x00,0x06,0x30,0x00,0x00,0x0E,0x38,0x00,0x00,0x0E,0x38,0x00,0x00,0x0C,0x18,0x00,0x00,0x00,0x00,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x7F,0xFF,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0xE3,0x00,0x00,0x00,0xE2,0x00,0x00,0x00,0xFC,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x00,0x00,0x01,0xE0,0x00,0x00,0x01,0xE0,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x0E,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x0E,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x0E,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"/",15*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0xF8,0x00,0x00,0x7F,0xFF,0x00,0x00,0xF0,0x07,0x80,0x01,0x80,0x00,0xC0,0x03,0x00,0x00,0x60,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0x00,0x00,0x60,0x01,0x80,0x00,0xC0,0x00,0xE0,0x03,0x80,0x00,0x7F,0xFF,0x00,0x00,0x0F,0xF8,0x00,0x00,0x00,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x20,0x00,0x80,0x00,0x20,0x00,0x80,0x00,0x20,0x00,0x80,0x00,0x60,0x01,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x00,0xE0,0x00,0x98,0x01,0x60,0x01,0x00,0x02,0x60,0x02,0x00,0x04,0x60,0x02,0x00,0x08,0x60,0x02,0x00,0x10,0x60,0x02,0x00,0x20,0x60,0x02,0x00,0x40,0x60,0x03,0x00,0x80,0x60,0x01,0x83,0x00,0x60,0x01,0xFE,0x00,0xE0,0x00,0x7C,0x07,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x07,0x80,0x01,0xF0,0x07,0xC0,0x01,0x00,0x00,0x40,0x02,0x00,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x03,0x03,0x80,0x20,0x01,0x86,0x80,0x40,0x01,0xFC,0xC0,0xC0,0x00,0x78,0x7F,0x80,0x00,0x00,0x1E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0x48,0x00,0x00,0x01,0x88,0x00,0x00,0x06,0x08,0x00,0x00,0x0C,0x08,0x10,0x00,0x30,0x08,0x10,0x00,0x40,0x08,0x10,0x01,0xFF,0xFF,0xF0,0x03,0xFF,0xFF,0xF0,0x03,0xFF,0xFF,0xF0,0x00,0x00,0x08,0x10,0x00,0x00,0x08,0x10,0x00,0x00,0x08,0x10,0x00,0x00,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x80,0x00,0x1F,0x86,0x40,0x03,0xE1,0x00,0x20,0x03,0x02,0x00,0x20,0x03,0x04,0x00,0x20,0x03,0x04,0x00,0x20,0x03,0x04,0x00,0x20,0x03,0x04,0x00,0x20,0x03,0x06,0x00,0x40,0x03,0x03,0x01,0xC0,0x03,0x01,0xFF,0x80,0x03,0x00,0x7E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xFC,0x00,0x00,0x3F,0xFF,0x00,0x00,0x70,0xC3,0x80,0x00,0x81,0x80,0xC0,0x01,0x01,0x00,0x60,0x03,0x02,0x00,0x20,0x02,0x02,0x00,0x20,0x02,0x02,0x00,0x20,0x02,0x02,0x00,0x20,0x02,0x03,0x00,0x40,0x01,0xC1,0x80,0xC0,0x00,0xC0,0xFF,0x80,0x00,0x00,0x7E,0x00,0x00,0x00,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0x80,0x00,0x00,0x03,0x00,0x00,0x00,0x03,0x00,0x07,0xE0,0x03,0x00,0x3F,0xE0,0x03,0x01,0xC0,0x00,0x03,0x06,0x00,0x00,0x03,0x18,0x00,0x00,0x03,0x60,0x00,0x00,0x03,0x80,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x00,0x00,0x78,0x3F,0x80,0x00,0xFC,0x60,0xC0,0x01,0x8E,0xC0,0x40,0x03,0x07,0x80,0x20,0x02,0x03,0x00,0x20,0x02,0x01,0x80,0x20,0x02,0x01,0x80,0x20,0x02,0x01,0xC0,0x20,0x03,0x01,0xE0,0x40,0x01,0x86,0x70,0xC0,0x00,0xFC,0x3F,0x80,0x00,0x78,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0xFF,0x81,0xC0,0x01,0xC0,0xC1,0xC0,0x01,0x00,0x60,0x20,0x02,0x00,0x20,0x20,0x02,0x00,0x20,0x20,0x02,0x00,0x20,0x20,0x02,0x00,0x20,0x60,0x02,0x00,0x40,0xC0,0x01,0x00,0xC1,0x80,0x00,0xC1,0x8F,0x00,0x00,0x7F,0xFE,0x00,0x00,0x1F,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0xC0,0x00,0x07,0x81,0xE0,0x00,0x07,0x81,0xE0,0x00,0x03,0x00,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x66,0x00,0x06,0x00,0x78,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x01,0xC0,0x00,0x00,0x03,0x60,0x00,0x00,0x06,0x30,0x00,0x00,0x0C,0x18,0x00,0x00,0x18,0x0C,0x00,0x00,0x30,0x06,0x00,0x00,0x60,0x03,0x00,0x00,0xC0,0x01,0x80,0x01,0x00,0x00,0x40,0x02,0x00,0x00,0x20,0x04,0x00,0x00,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x10,0x02,0x00,0x00,0x20,0x01,0x00,0x00,0x40,0x00,0xC0,0x01,0x80,0x00,0x60,0x03,0x00,0x00,0x30,0x06,0x00,0x00,0x18,0x0C,0x00,0x00,0x0C,0x18,0x00,0x00,0x06,0x30,0x00,0x00,0x03,0x60,0x00,0x00,0x01,0xC0,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x00,0x00,0x01,0xF8,0x00,0x00,0x02,0x38,0x00,0x00,0x02,0x00,0x00,0x00,0x04,0x00,0x00,0xC0,0x04,0x00,0x79,0xE0,0x04,0x00,0x81,0xE0,0x04,0x01,0x00,0xC0,0x04,0x03,0x00,0x00,0x02,0x02,0x00,0x00,0x03,0x06,0x00,0x00,0x01,0xFC,0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0xF8,0x00,0x00,0x3F,0xFE,0x00,0x00,0x70,0x07,0x80,0x00,0xC0,0x00,0xC0,0x01,0x01,0xF8,0x40,0x03,0x07,0xFC,0x20,0x02,0x1E,0x04,0x20,0x02,0x30,0x08,0x20,0x02,0x20,0x30,0x20,0x02,0x3F,0xFC,0x20,0x01,0x3F,0x04,0x40,0x01,0x80,0x0C,0xC0,0x00,0xE0,0x31,0x80,0x00,0x1F,0xC2,0x00,0x00,0x00,0x00,0x00},/*"@",32*/
{0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x60,0x00,0x00,0x03,0xE0,0x00,0x00,0x3E,0x20,0x00,0x03,0xE0,0x20,0x00,0x3E,0x20,0x00,0x03,0xE0,0x20,0x00,0x03,0x80,0x20,0x00,0x07,0xFC,0x20,0x00,0x00,0x3F,0xE0,0x00,0x00,0x03,0xFE,0x20,0x00,0x00,0x3F,0xE0,0x00,0x00,0x01,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"A",33*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x03,0x03,0x00,0x20,0x01,0x86,0x80,0x60,0x01,0xFC,0xC0,0xC0,0x00,0xF8,0x7F,0x80,0x00,0x00,0x1F,0x00,0x00,0x00,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x00,0x00,0x07,0xF8,0x00,0x00,0x3F,0xFF,0x00,0x00,0x70,0x07,0x80,0x00,0xC0,0x00,0xC0,0x01,0x00,0x00,0x40,0x03,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x01,0x00,0x00,0x40,0x01,0x80,0x00,0xC0,0x03,0xC0,0x01,0x80,0x00,0x30,0x06,0x00,0x00,0x00,0x00,0x00},/*"C",35*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0x00,0x00,0x60,0x01,0x00,0x00,0x40,0x01,0x80,0x00,0xC0,0x00,0xF0,0x07,0x80,0x00,0x7F,0xFE,0x00,0x00,0x0F,0xF8,0x00,0x00,0x00,0x00,0x00},/*"D",36*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x03,0x80,0x20,0x02,0x0F,0xE0,0x20,0x03,0x00,0x00,0x60,0x03,0xC0,0x00,0xE0,0x00,0x60,0x03,0x00,0x00,0x00,0x00,0x00},/*"E",37*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x00,0x02,0x01,0x00,0x00,0x02,0x01,0x00,0x00,0x02,0x01,0x00,0x00,0x02,0x03,0x80,0x00,0x03,0x0F,0xE0,0x00,0x03,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x00,0x60,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x00,0x00,0x07,0xF8,0x00,0x00,0x3F,0xFE,0x00,0x00,0x70,0x07,0x80,0x01,0xC0,0x01,0xC0,0x01,0x00,0x00,0x40,0x03,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x01,0x00,0x20,0x20,0x01,0x00,0x20,0x40,0x03,0xC0,0x3F,0x80,0x00,0x30,0x3F,0x80,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00},/*"G",39*/
{0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x80,0x20,0x02,0x00,0x80,0x20,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x02,0x00,0x80,0x20,0x02,0x00,0x80,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"H",40*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0E,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x01,0x02,0x00,0x00,0x01,0x02,0x00,0x00,0x01,0x02,0x00,0x00,0x03,0x02,0x00,0x00,0x06,0x03,0xFF,0xFF,0xFC,0x03,0xFF,0xFF,0xF8,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"J",42*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0xC0,0x20,0x02,0x01,0x00,0x20,0x00,0x07,0x80,0x00,0x00,0x0F,0xE0,0x00,0x00,0x30,0xF8,0x00,0x02,0x60,0x3E,0x20,0x03,0x80,0x0F,0x20,0x03,0x00,0x03,0xE0,0x02,0x00,0x00,0xE0,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x20},/*"K",43*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00},/*"L",44*/
{0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xE0,0x00,0x20,0x03,0xFF,0x00,0x20,0x00,0x1F,0xF0,0x00,0x00,0x01,0xFF,0x80,0x00,0x00,0x0F,0xE0,0x00,0x00,0x1E,0x00,0x00,0x03,0xE0,0x00,0x00,0x3E,0x00,0x20,0x03,0xE0,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20},/*"M",45*/
{0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0x80,0x00,0x20,0x03,0xF0,0x00,0x20,0x00,0xFC,0x00,0x00,0x00,0x1F,0x00,0x00,0x00,0x07,0xC0,0x00,0x00,0x01,0xF0,0x00,0x00,0x00,0x7C,0x00,0x02,0x00,0x1F,0x80,0x02,0x00,0x07,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0xF8,0x00,0x00,0x3F,0xFE,0x00,0x00,0xF0,0x07,0x80,0x01,0x80,0x00,0xC0,0x01,0x00,0x00,0x40,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x01,0x00,0x00,0x40,0x01,0x80,0x00,0xC0,0x00,0xF0,0x03,0x80,0x00,0x3F,0xFE,0x00,0x00,0x0F,0xF8,0x00,0x00,0x00,0x00,0x00},/*"O",47*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x80,0x20,0x02,0x00,0x80,0x20,0x02,0x00,0x80,0x00,0x02,0x00,0x80,0x00,0x02,0x00,0x80,0x00,0x02,0x00,0x80,0x00,0x03,0x01,0x80,0x00,0x01,0x83,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x7C,0x00,0x00,0x00,0x00,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0xF8,0x00,0x00,0x7F,0xFF,0x00,0x00,0xF0,0x03,0x80,0x01,0x80,0x01,0xC0,0x01,0x00,0x06,0x40,0x02,0x00,0x04,0x20,0x02,0x00,0x04,0x20,0x02,0x00,0x06,0x20,0x02,0x00,0x03,0xE0,0x01,0x00,0x00,0xF8,0x01,0x80,0x00,0x5C,0x00,0xE0,0x03,0x8C,0x00,0x3F,0xFF,0x0C,0x00,0x0F,0xFC,0x18,0x00,0x00,0x00,0x00},/*"Q",49*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x80,0x00,0x02,0x01,0xE0,0x00,0x02,0x01,0xFC,0x00,0x03,0x03,0x3F,0x80,0x01,0x86,0x07,0xE0,0x01,0xFC,0x00,0xE0,0x00,0xF8,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"R",50*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x06,0x00,0x00,0xFE,0x01,0xE0,0x01,0x86,0x00,0xC0,0x03,0x03,0x00,0x40,0x02,0x03,0x00,0x20,0x02,0x01,0x80,0x20,0x02,0x01,0x80,0x20,0x02,0x01,0xC0,0x20,0x02,0x00,0xC0,0x20,0x01,0x00,0xE0,0x60,0x01,0x80,0x70,0xC0,0x03,0xE0,0x3F,0x80,0x00,0x00,0x1F,0x00,0x00,0x00,0x00,0x00},/*"S",51*/
{0x00,0x00,0x00,0x00,0x00,0x60,0x00,0x00,0x03,0x80,0x00,0x00,0x03,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0x80,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"T",52*/
{0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0xFF,0xFF,0x00,0x03,0xFF,0xFF,0xC0,0x02,0x00,0x00,0x40,0x02,0x00,0x00,0x60,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x02,0x00,0x00,0x40,0x02,0x00,0x00,0x80,0x03,0xFF,0xFF,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"U",53*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xFC,0x00,0x00,0x02,0x3F,0xC0,0x00,0x00,0x03,0xF8,0x00,0x00,0x00,0x7F,0x80,0x00,0x00,0x07,0xE0,0x00,0x00,0x07,0x80,0x00,0x00,0x78,0x00,0x02,0x03,0xC0,0x00,0x02,0x3C,0x00,0x00,0x03,0xC0,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00},/*"V",54*/
{0x02,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xFF,0x80,0x00,0x02,0x3F,0xFE,0x00,0x02,0x00,0x7F,0xE0,0x00,0x00,0x0F,0x00,0x02,0x00,0xF0,0x00,0x03,0xEF,0x00,0x00,0x03,0xFF,0x80,0x00,0x02,0x0F,0xFE,0x00,0x00,0x00,0x3F,0xE0,0x00,0x00,0x1F,0x00,0x02,0x07,0xE0,0x00,0x03,0xF8,0x00,0x00,0x03,0x00,0x00,0x00,0x02,0x00,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0x80,0x00,0xE0,0x03,0xF0,0x03,0x20,0x02,0xFC,0x0C,0x20,0x02,0x1F,0x30,0x00,0x00,0x07,0xC0,0x00,0x00,0x07,0xF0,0x00,0x02,0x18,0x7C,0x00,0x02,0x60,0x1F,0x20,0x03,0x80,0x03,0xE0,0x02,0x00,0x00,0xE0,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"X",56*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xF8,0x00,0x00,0x02,0x3E,0x00,0x20,0x02,0x0F,0xC0,0x20,0x00,0x01,0xFF,0xE0,0x00,0x00,0x7F,0xE0,0x00,0x03,0x80,0x20,0x02,0x1C,0x00,0x20,0x02,0x70,0x00,0x00,0x03,0x80,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x60,0x00,0xE0,0x03,0x80,0x03,0xE0,0x03,0x00,0x0F,0xA0,0x02,0x00,0x3E,0x20,0x02,0x00,0xF8,0x20,0x02,0x03,0xE0,0x20,0x02,0x0F,0x80,0x20,0x02,0x3E,0x00,0x20,0x02,0x78,0x00,0x20,0x03,0xE0,0x00,0x60,0x03,0x80,0x00,0xE0,0x02,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xFF,0xFF,0xFC,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"[",59*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x1E,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x1E,0x00,0x00,0x00,0x07,0x80,0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"\",60*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x1F,0xFF,0xFF,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x10,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01},/*"_",63*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x00,0x10,0x00,0x00,0x00,0x10,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x80,0x00,0x01,0x8F,0xC0,0x00,0x03,0x8C,0x60,0x00,0x06,0x18,0x20,0x00,0x04,0x10,0x20,0x00,0x04,0x10,0x20,0x00,0x04,0x20,0x20,0x00,0x04,0x20,0x40,0x00,0x06,0x20,0x40,0x00,0x03,0xFF,0xC0,0x00,0x01,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0x00},/*"a",65*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xC0,0x00,0x01,0x80,0xC0,0x00,0x02,0x00,0x60,0x00,0x02,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x40,0x00,0x03,0x00,0xC0,0x00,0x01,0xFF,0x80,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x01,0xFF,0x80,0x00,0x03,0x81,0xC0,0x00,0x02,0x00,0x40,0x00,0x06,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x03,0xC0,0x40,0x00,0x01,0xC0,0x80,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x01,0xFF,0x80,0x00,0x03,0x80,0xC0,0x00,0x06,0x00,0x60,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x02,0x04,0x00,0x40,0x02,0x02,0x00,0x80,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xC0,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x01,0xFF,0x80,0x00,0x03,0x11,0xC0,0x00,0x02,0x10,0x40,0x00,0x04,0x10,0x60,0x00,0x04,0x10,0x20,0x00,0x04,0x10,0x20,0x00,0x04,0x10,0x20,0x00,0x06,0x10,0x20,0x00,0x03,0x10,0x40,0x00,0x01,0xF0,0xC0,0x00,0x00,0x71,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x7F,0xFF,0xE0,0x01,0xFF,0xFF,0xE0,0x01,0x04,0x00,0x20,0x03,0x04,0x00,0x20,0x02,0x04,0x00,0x20,0x02,0x04,0x00,0x20,0x02,0x04,0x00,0x00,0x02,0x00,0x00,0x00,0x01,0xC0,0x00,0x00,0x01,0xC0,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x00,0x00,0xE3,0x3E,0x00,0x03,0xFF,0xC2,0x00,0x02,0x0C,0xC3,0x00,0x04,0x04,0xC1,0x00,0x04,0x04,0xC1,0x00,0x04,0x04,0xC1,0x00,0x04,0x04,0xC1,0x00,0x06,0x0C,0xC1,0x00,0x03,0xF8,0xC3,0x00,0x05,0xF0,0x62,0x00,0x06,0x00,0x7E,0x00,0x06,0x00,0x3C,0x00,0x00,0x00,0x00},/*"g",71*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xE0,0x00,0x01,0x00,0x20,0x00,0x02,0x00,0x20,0x00,0x06,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x03,0xFF,0xE0,0x00,0x01,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20},/*"h",72*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x03,0x87,0xFF,0xE0,0x03,0x8F,0xFF,0xE0,0x03,0x80,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x03,0x00,0x04,0x00,0x06,0x03,0x87,0xFF,0xFC,0x03,0x8F,0xFF,0xF8,0x03,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"j",74*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xE0,0x00,0x00,0x08,0x20,0x00,0x00,0x10,0x20,0x00,0x00,0x30,0x00,0x00,0x00,0xFC,0x00,0x00,0x05,0x8E,0x00,0x00,0x07,0x07,0xA0,0x00,0x06,0x01,0xE0,0x00,0x04,0x00,0xE0,0x00,0x04,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"l",76*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x07,0xFF,0xE0,0x00,0x0F,0xFF,0xE0,0x00,0x02,0x00,0x20,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x07,0xFF,0xE0,0x00,0x03,0xFF,0xE0,0x00,0x02,0x00,0x20,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x07,0xFF,0xE0,0x00,0x03,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"m",77*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x07,0xFF,0xE0,0x00,0x0F,0xFF,0xE0,0x00,0x01,0x00,0x20,0x00,0x02,0x00,0x20,0x00,0x02,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x03,0xFF,0xE0,0x00,0x01,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20},/*"n",78*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x00,0xFF,0x80,0x00,0x03,0x81,0xC0,0x00,0x02,0x00,0x40,0x00,0x06,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x02,0x00,0x40,0x00,0x03,0x81,0xC0,0x00,0x01,0xFF,0x80,0x00,0x00,0x7E,0x00,0x00,0x00,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x07,0xFF,0xFF,0x00,0x0F,0xFF,0xFF,0x00,0x01,0x00,0xC1,0x00,0x02,0x00,0x41,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x40,0x00,0x03,0x01,0xC0,0x00,0x01,0xFF,0x80,0x00,0x00,0x7E,0x00,0x00,0x00,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x01,0xFF,0x80,0x00,0x03,0x80,0xC0,0x00,0x02,0x00,0x60,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x02,0x00,0x41,0x00,0x03,0x00,0xC1,0x00,0x03,0xFF,0xFF,0x00,0x07,0xFF,0xFF,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01},/*"q",81*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x0F,0xFF,0xE0,0x00,0x0F,0xFF,0xE0,0x00,0x00,0xC0,0x20,0x00,0x01,0x00,0x20,0x00,0x02,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xE0,0x00,0x01,0xC0,0xE0,0x00,0x03,0xE0,0x40,0x00,0x06,0x30,0x20,0x00,0x04,0x30,0x20,0x00,0x04,0x18,0x20,0x00,0x04,0x18,0x20,0x00,0x04,0x18,0x20,0x00,0x04,0x0C,0x20,0x00,0x02,0x0C,0x60,0x00,0x03,0x07,0xC0,0x00,0x07,0x83,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x0C,0x00,0x00,0x00,0x1F,0xFF,0x80,0x00,0xFF,0xFF,0xC0,0x00,0x04,0x00,0x60,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x40,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x07,0xFF,0x80,0x00,0x0F,0xFF,0xC0,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x04,0x00,0x40,0x00,0x04,0x00,0x80,0x00,0x07,0xFF,0xE0,0x00,0x0F,0xFF,0xC0,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40},/*"u",85*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0xF0,0x00,0x00,0x04,0xFE,0x00,0x00,0x04,0x1F,0xC0,0x00,0x00,0x03,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x1C,0x00,0x00,0x04,0x60,0x00,0x00,0x07,0x80,0x00,0x00,0x06,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"v",86*/
{0x00,0x04,0x00,0x00,0x00,0x06,0x00,0x00,0x00,0x07,0xC0,0x00,0x00,0x07,0xFC,0x00,0x00,0x04,0x3F,0x80,0x00,0x00,0x03,0xE0,0x00,0x04,0x0F,0x80,0x00,0x06,0xF0,0x00,0x00,0x07,0xF0,0x00,0x00,0x07,0xFF,0x80,0x00,0x04,0x0F,0xE0,0x00,0x00,0x03,0x80,0x00,0x04,0x3C,0x00,0x00,0x07,0xC0,0x00,0x00,0x06,0x00,0x00,0x00,0x04,0x00,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x60,0x00,0x07,0x00,0xE0,0x00,0x07,0x83,0x20,0x00,0x07,0xE6,0x00,0x00,0x04,0xF8,0x00,0x00,0x00,0x3C,0x00,0x00,0x04,0x5E,0x20,0x00,0x05,0x87,0xA0,0x00,0x06,0x01,0xE0,0x00,0x04,0x00,0x60,0x00,0x04,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x03,0x00,0x07,0x00,0x03,0x00,0x07,0xE0,0x01,0x00,0x04,0xF8,0x01,0x00,0x04,0x1F,0x02,0x00,0x00,0x07,0xFC,0x00,0x00,0x00,0xE0,0x00,0x00,0x07,0x00,0x00,0x04,0x38,0x00,0x00,0x07,0xC0,0x00,0x00,0x06,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x80,0x60,0x00,0x06,0x00,0xE0,0x00,0x04,0x03,0xE0,0x00,0x04,0x07,0xA0,0x00,0x04,0x0E,0x20,0x00,0x04,0x3C,0x20,0x00,0x04,0x70,0x20,0x00,0x05,0xE0,0x20,0x00,0x07,0x80,0x20,0x00,0x07,0x00,0x60,0x00,0x04,0x00,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x01,0x40,0x00,0x07,0xFE,0x3F,0xF8,0x08,0x00,0x00,0x04,0x10,0x00,0x00,0x02,0x10,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x02,0x10,0x00,0x00,0x02,0x08,0x00,0x00,0x04,0x07,0xFE,0x3F,0xF8,0x00,0x01,0x40,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x30,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x30,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x0C,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/
};
#endif
向工程中添加.c/.h文件的步骤请阅读“
STM32CubeMX教程19 I2C - MPU6050驱动
”实验3.2.3小节
值得提醒的是在LCD初始化函数中使用串口打印了LCD的控制芯片ID，因此如果未初始化串口请注释掉该输出代码
，如果你不希望注释，请阅读“
STM32CubeMX教程9 USART/UART 异步通信
”配置并重定向串口
然后在主函数中添加一些用于测试LCD是否正常工作的函数，具体源代码如下所示
/*LCD测试函数*/
void LCD_TEST(void)
{
/*画线测试*/
testlines();
HAL_Delay(1000);
/*画正方形测试*/
testdrawrects();
HAL_Delay(1000);
/*画圆测试*/
testfillcircles(15);
HAL_Delay(1000);
/*字体测试*/
tftPrintTest();
}
/*画线测试*/
void testlines(void)
{
LCD_Clear(WHITE);
POINT_COLOR=BLACK;
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawLine(0, 0, x, SSD_HOR_RESOLUTION-1);
HAL_Delay(3);
}
for (int16_t y=0; y < SSD_HOR_RESOLUTION; y+=6)
{
LCD_DrawLine(0, 0, SSD_VER_RESOLUTION-1, y);
HAL_Delay(3);
}
LCD_Clear(WHITE);
POINT_COLOR=BLUE;
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawLine(SSD_VER_RESOLUTION-1, 0, x, SSD_HOR_RESOLUTION-1);
HAL_Delay(3);
}
for (int16_t y=0; y < SSD_HOR_RESOLUTION; y+=6)
{
LCD_DrawLine(SSD_VER_RESOLUTION-1, 0, 0, y);
HAL_Delay(3);
}
LCD_Clear(WHITE);
POINT_COLOR=RED;
for (int16_t y=0; y < SSD_HOR_RESOLUTION; y+=6)
{
LCD_DrawLine(0, SSD_HOR_RESOLUTION-1, SSD_VER_RESOLUTION-1, y);
HAL_Delay(3);
}
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawLine(0, SSD_HOR_RESOLUTION-1, x, 0);
HAL_Delay(3);
}
LCD_Clear(WHITE);
POINT_COLOR=MAGENTA;
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawLine(SSD_VER_RESOLUTION-1, SSD_HOR_RESOLUTION-1, x, 0);
HAL_Delay(3);
}
for (int16_t y=0; y < SSD_HOR_RESOLUTION; y+=6)
{
LCD_DrawLine(SSD_VER_RESOLUTION-1, SSD_HOR_RESOLUTION-1, 0, y);
HAL_Delay(3);
}
}
/*画正方形测试*/
void testdrawrects(void)
{
LCD_Clear(WHITE);
POINT_COLOR=BLACK;
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawRectangle(SSD_VER_RESOLUTION/2 -x/2, SSD_HOR_RESOLUTION/2 -x/2 , x, x);
}
}
/*画圆测试*/
void testfillcircles(uint8_t radius)
{
LCD_Clear(WHITE);
POINT_COLOR=BLUE;
for(int16_t x=radius; x < SSD_VER_RESOLUTION; x+=radius*2)
{
for(int16_t y=radius; y < SSD_HOR_RESOLUTION; y+=radius*2)
{
LCD_Draw_Circle(x, y, radius);
}
}
HAL_Delay(1500);
LCD_Clear(WHITE);
POINT_COLOR=MAGENTA;
radius = radius / 2;
for(int16_t x=radius; x < SSD_VER_RESOLUTION; x+=radius*2)
{
for(int16_t y=radius; y < SSD_HOR_RESOLUTION; y+=radius*2)
{
LCD_Draw_Circle(x, y, radius);
}
}
}
/*字体测试*/
void tftPrintTest(void)
{
LCD_Clear(WHITE);
LCD_SetCursor(0, 30);
POINT_COLOR=RED;
LCD_ShowString(0,30,200,16,16,(uint8_t *)"Hello World!");
POINT_COLOR=YELLOW;
LCD_ShowString(0,60,200,16,24,(uint8_t *)"Hello World!");
POINT_COLOR=GREEN;
LCD_ShowString(0,90,200,16,32,(uint8_t *)"Hello World!");
POINT_COLOR=BLUE;
LCD_ShowxNum(0,120,1234,4,24,1);
HAL_Delay(1500);
POINT_COLOR=YELLOW;
LCD_ShowString(0,180,200,16,24,(uint8_t *)"Hello World!");
POINT_COLOR=GREEN;
LCD_ShowString(0,210,200,16,32,(uint8_t *)" Want pi?");
LCD_ShowString(0,240,200,16,32,(uint8_t *)" Print HEX!");
POINT_COLOR=BLUE;
LCD_ShowString(0,270,200,16,16,(uint8_t *)"Sketch has been");
LCD_ShowString(0,300,200,16,24,(uint8_t *)"running for: ");
POINT_COLOR=MAGENTA;
LCD_ShowString(0,330,200,16,24,(uint8_t *)" seconds.");
}
在main.c中声明这些用于测试的函数
void LCD_TEST(void);
void testlines(void);
void testdrawrects(void);
void testfillcircles(uint8_t radius);
void tftPrintTest(void);
最后在主函数中对LCD初始化，在主循环中周期调用测试函数即可，具体源代码如下所示
/*主循环外程序*/
//这个延时在FSMC初始化之后LCD初始化之前，必须要有
HAL_Delay(50);
LCD_Init();
/*主循环内程序*/
LCD_TEST();
HAL_Delay(4000);
4、烧录验证
烧录程序，开发板上电后，LCD会依次测试画线、画矩形、画圆和字符输出功能，具体现象如下图所示
5、注释详解
注释1
：图片来源 STM32F4xx 中文参考手册 RM009
注释2
：图片来源
https://github.com/hampussandberg/HexConnect/wiki/LCD-ER_TFTM070_5
注释3
：图片来源
STM32Cube高效开发教程（基础篇）
注释4
：NT35510数据手册来源
https://www.waveshare.com/w/upload/a/a8/NT35510.pdf
注释5
：IL9341数据手册来源
https://cdn-shop.adafruit.com/datasheets/ILI9341.pdf
注释6
：NT35510芯片LCD驱动程序来自正点原子